Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I try to make a simple project based on a "simple message model" ( https://devzone.nordicsemi.com/f/nordic-q-a/29836/send-and-receive-a-string-via-access-layer ) with Mesh...
Hi，
SDK：nRF5_SDK_15.0.0_a53641a
Chip：nRF52810
Example BLE：ble_app_uart（pca10040e \ s112）
Example 2.4G：esb_prx（pca10040）
I am working on BLE and 2.4G integration...
Hi，
I use SDK is ：nRF5_SDK_15.0.0_a53641a
But the SDK version in the link seems to be lower
devzone.nordicsemi.com/.../setting-up-the-timeslot-api
I am going to step...
I'm developing an application to communicate with a smartphone. I have the need of writing characteristics with the size bigger than the negotiated MTU, so I'm exploring Queued...
Hi guys, our team now are trying to used nrf52832 to stream audio to ios app, and as you know we are in trouble.
Here are some info about our test env:
1. mobile app...
Hi everyone,
I wanted to add a second UART (UARTE1) to the CLI example in the OpenThread SDK 0.10.0 since UART0 is used by CLI but I was not able to find any documentation...
Hi,
Can't get rid of compilation error about undefined NRFX_SPI0_INST_IDX after adding nrfx_spi driver. Searched the forums and found similar issues but none of the suggested...
Sir,
Did you succesfully compile the NRF5 mesh on SEGGER STUDIO ? I did try with updated segger but i am getting the same error!
And i cant see too the sdk_config.h to...
Hi,
I just received nRF52-DK recently.
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux...
Hi, I am developing an SPIS interface on the nRF51822 using SDK v12.3.
I have configured my device for EasyDMA and I expected to see a continuous stream of data being transmitted...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project to get thing'y motion sensor by nRF52840 DK.
When I init DK, it discovered only 7 UUID so euler,...
Hi Everyone
I am trying to use BME which is an i2c/twi sensor and EPaper which is an SPI based module. In my code i am using TWI INSTANCE ID 0 AND SPI INSTANCE ID 0.
I...
Hi all:
I am developing the driver of ST LIS3DH and its mcu is NRF52.
If I want to read the value of whoami.
I am not sure if I need call the function of
nrf_drv_twi_tx...
