Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi all i am facing few problem after checking the power consumption of the nRF52832 using the Power profiler kit. I followed the demo video in the link ( https://www.nordicsemi...
Could you please check whether 52840 can support memory map to QSPI PSRAM on QSPI interface?
If yes, that means the compiler would see a big RAM space of 2~8MB QSPI PSRAM...
hello，all
NRF_RADIO->CRCCNF
NRF_RADIO->CRCPOLY
NRF_RADIO->CRCINIT
If the register setting are different, can rx device recieve the message from tx device? whether...
Hi,
I use the peripheral ble_app_uart with nRF52832 (Murata module). The nRF52832 is connected to another MCU, STM32L476, via UART.
I develop using IAR, with SDK V15.0...
Hi All,
Enter to Direct Test Mode, the nRF52832 will transmit 2426MHz channel frequnicy only when set any different frequency channels (e.g. 2402MHz, 2418MHz) in the Tx...
Hello,
I don't understand why the ble_advdata_short_name_find function never return a true value. I'm sure that I send a short name because I verified this on the nRF connect...
Hello, I want to synchronize several peripherals with a central, I already tried to do it with the state of the gpiote but I did not have the expected result at the level...
Hi
I'm facing a Hard fault on the softdevice when trying to call sd_ble_gattc_write(). SDK15, SD140
I have a Multilink central connected to UART using app_uart. when a...
I have been doing a bit of searching and reading but I'm none the wiser.
I have a client that uses lots of BLE nRF51822 based modules made by Raytac Corporation in a classroom...
I am converting Arduino BNO080 library ( github.com/.../SparkFun_BNO080_Arduino_Library) to nRF52832.
Specifically, this is a function for sending a SHTP packet over I2C...
hi to all,
i had developed a device with NRF51822 wih S130 and i want to port my application to new NRF52840 soc S140 and SDK15, S130 has an structure that let me to limit...
Below are the symptoms, but it turns out the problem was quite simple: the device is not seem capable of scanning while at the same time being connected, unless you use a...
Hello,
I have a problem where the nRF52840 is not advertising. The code runs in the debugger but there is no radio signal. I've already sent the schematic and layout....
Is there an easy way to check what the current connection's agreed upon MTU is?
I'm connecting to random devices that all have different intervals and MTUs. I can't be sure...
When I use saadc to sample battery's power,the software restart ceaselessly.I use the steps as following:
1.void saadc_init(void).
2.void saadc_callback(nrf_drv_saadc_evt_t...
