Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I been trying to figure this out but to no avail. I get these errors on build.
:/ncs/toolchains/b620d30767/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi...
Using the "launcher" the open button appears to do nothing and the update from V4.2.0 to V4.2.1 produces an error message.
Twice I have uninstalled V5.1.0 and replaced it...
I'm using an nfr52840 board.
I noticed that when using The 'zephry-sdk' v3.5.99-ncs1-1, when doing a passive scan using:
BT_LE_SCAN_ PASSIVE
which sets:
BT_LE_SCAN_PARAM...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message with a something hits the device. To achieve this...
To output PWM signal as early as possible after powering on the NRF5340DK, I added the same code in mcuboot/boot/zephy/main.c and mcuboot.overlay as in the app core. This...
I reference the sample at https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise-3-interfacing...
I have a packet that I am sending out using the nrf52840. Using another piece of code supplied by Emil Lenngren, information from the solar_sensor_beacon project and raw data...
Hi,
I am using the NRF52840 dongles for BLE communication with S140 and the NRF5 17.1.0 SDK. I have plugged each dongle in a Raspberry Pi 3B+, and have set the DCDC regulator...
Hi, We are developing a product which is reading RTDs and thermistors from the NRF52833's internal ADC. We're working on compensating for the intrinsic errors of the ADC and...
Hello,
In my device I have a nrf52840 which communicates with a STM32 via uart.
In my nrf52840 I use the MCUboot.
Is there any documentation or source code that would...
Hi all,
I am developing my own provisioner with the nrf52840 chip. My idea is to be able to add at least 2000 nodes to a bluetooth mesh network with the provisioner but...
Hi, I'm delevoping an appilcation which can generate one sample per 20 us (accomplished with timer0) and transmit one ESB packet when 20 samples are collected. Below is the...
I'm using NCS 2.7.0 and NCS 2.9.0 to read the BT stack version information on an nRF5340. See below for the results.
How should the fw_version, fw_revision, and fw_build...
Hello Nordic-team,
I´m currently developing an application which has been based on a 54L15DK an I´m using an overlay file for adjusting the ports to my own hardware. That...
I/ trying to read the ID of a Fijitsu FRAM type MB85RS4MT using the Nordic device nRF5340. I can properly initialize the SPI and transmit the RDID =0x9F command. The FRAM...
