I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
Hello, we currently use nRF52832 in our product. For the next generation of this product, we are hoping to upgrade to a new module that uses nRF52833. However, this is only...
We have a well-vetted software environment what uses SDK 15.3.0 and softdevice s132. We are considering adding ANT+ to our environment, which as I understand requires that...
I am in the process of bringing up a custom board with an nrf5340 and a FUSB302B USB-C PHY-controller.
As a driver for the FUSB203B, I am using this project as an OOT-module...
Hello
Due to some reasons we need to use external antenna and RF cables.
What is a part number of the antenna that can be connected to the J1 RF Antenna connector?
We...
Hi,
I am implemented the uart functionality, I'm getting below issue.
[00:00:00.445,526] <err> Throughput: Failed to set UART callback (err -88) [00:00:00.445,556] <err...
I want to use LPCOMP in nrf52832 to detect a rising edge of voltage. And my code is:
I set the reference as NRF_LPCOMP_INPUT_1 or NRF_LPCOMP_REF_SUPPLY_4_8, the event is...
I am running on openthread demo: ot_cli on its low power mode by building with low_power snippet.
As document says, it will automatically suspend UART operation when low...
Hi,
I'm trying to use to gpio pins in order to wake up a system from sleep mode.(PIN1= P0.24 PIN2 =P1.1 )
If I use the GPIOTEs separately in my project, it works and sytem...
There are some serious issues in the file "board.c" that relate to LEDS_NUMBER.
If I create a custom board with no LEDs then I set LEDS_NUMBER to in my custom boards,h....
Hello,
My company has developed a Bluetooth application that runs on the nRF52832 and we are about to perform FCC pre-scan testing next week. In order to prepare for this...
I want to use one device (nrf5340 audio DK) as both a gateway and a headset. Is this possible?
It needs to both receive audio from a CIS gateway and send it out, working...
Hi Team, I need to integrate FreeRTOS into the ble_app_hrs_nfc_pairing example. What are the ways to integrate FreeRTOS into ble_app_hrs_nfc_pairing? I need to create two...
I have bought an nrf9161-dk and following the documentation, I was installing the asset tracker using nrf-desktop v.4.4.1 (because v.5.0 crashes everytime I open it in full...
I am aiming to connect the Gateway and Headset 1:1 and output stereo from the Headset.
The Gateway side is 16-bit I2S and the Headset side is 32-bit I2S, and I am able to...
