Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
Hello Nordic.
Hardware: nrf54lm20A-DK v0.3.4
SDK: 3.4.2
sample: spi_flash
Initially, I tested read/write operations on an external flash using the `spi_flash` example...
For nrf Connect SDK, can I config CONFIG_BT_ID_MAX = 2, both adress type are Public for below use case?
ID with index = 0 for peripheral role and for connect and bonded...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
My desired work flow is the following.
Input: Two electret microphones -> Audio ADC -> I2S Stereo -> nrf5340
Processing: Buffers (10-50 bytes) channel 2 to create delay...
We are investigating an intermittent Bluetooth Mesh LPN issue on the nRF54L15, where the LPN state machine becomes stuck in BT_MESH_LPN_ESTABLISHED even though the Friendship...
Hi,
On the nRF93M1 DK, we can switch between physical SIM and eSIM with %SIMCFG="SimSlot" (mfw 1.5.0).
1. Is SimSlot written to NVM on set, or in the flush at CFUN=0?...
We are implementing key handling for the nRF5340 and have come across an inconsistency between the CC312 and Oberon key management drivers. I wanted to verify if this inconsistency...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
With PM device runtime enabled ( CONFIG_PM_DEVICE_RUNTIME =y ), calling uart_irq_tx_disable (actual driver function uarte_nrfx_irq_tx_disable) may result in increase the PM...
