I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello,
I would like to know if there is official C# source code to perform DFU OTA for a NRF52840 from Windows without Nordic hardware (DK, dongles etc..), using only the...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hi
I am getting an error while building source code. The same code used to build while using NRF connect SDK version 2.5.1. Currently I am using nRF Connect SDK version...
Hi,
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
Hi, We are using `fota_download` library on our nRF9161 design running mfw-nrf91x1_2.0.1 to download a firmware upgrade image from our Amazon AWS server location. When trying...
Hello, I am currently using (\nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio\receiver)routine to develop.I want to check if the first N bytes of the received packet are...
Hi! I am using nrf32840 with free rtos,
and I have a loop that do the following
for(;;){
vTaskDelay(pdMS_TO_TICKS(intervalTime)); // go to sleep due to portSUPPRESS_TICKS_AND_SLEEP...
Hello guys, W are using the nRF52840 development kit in our project, we received the development kit today and when we powered the kit to my laptop(Acer nitro 5) using a micro...
Hello guys
I'm using nRf52840 development for my project, when trying to connect using a micro USB to the laptop, the J Link drive is not being detected on my laptop(Acer...
I am trying to program nrf52840 to print acceleration from mpu6050. But when I build the project, I get the error - undefined reference to `nrf_drv_twi_init'. Here is the...
Hi Support, we are using custom hardware and the follwoing versions:
1. modem - 1.3.4
2. nrf-sdk - 1.9.0
3. Zephyr - v2.7.99
Our application is based on the gnss sample...
Hi
We built an application that bases on the sample application "central_and_peripheral_hr" with NCS v2.7.0 and nRF54L15.
In this application, I tried to manually start...