Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hi
I have similar question to the post https://devzone.nordicsemi.com/f/nordic-q-a/7013/nrf51822-internal-ldo-output-pin .
I need a stable voltage to elevate the reference...
Hello everyone,
I use the multirole software as base for my application and I programmed everything with a evaluation board. I design my own PCB and decided to not use the...
Hi,
Is there any sample in nRF_Connect_SDK that implements RTC on nrf52840 SoC?
I need to implement RTC in my application, so is there any example reference for this...
Hello,
I am trying to set the `BT_SHELL_NUS` project up as a standalone repository. My requirements for this are as follows: I only want to commit application code to git...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We had to change the SDK version to 1.9.1 from...
I am trying to implement RSA signing into my application, I am planning to use the following example as a starting point but the sample, with no modification appears to not...
Hi there,
We are developing on the NRF5340, and have a question regarding the drive strength that can be set on a GPIO pin using the PIN_CNF register.
However we can not...
Hello,
i am using the nrf52810, ble_app_template example to read Accelerometer and gyro-meter data from ICM42605 sensor. so i have followed the i2c communication tutorial...
Hi there,
We are not able to find the reset due to brownout within the RESET->RESETREAS register? Is this the case? There are explanations of the brownout detection in the...
I'm trying to get DFU working with LPN on the 833. The sequence I follow is: (Erase board) Flash Soft Device Flash Bootloader (Using mesh, but don't want serial)
Flash Device...
Hi,
I'm trying to setup a very basic network based on the thread CLI example.
I have an nrf52840-dk as a router/commissioner and a custom device as a nrf52840 joiner...
This is the next step of the process getting the canbus working with nrf9160 and the aditional MKR CAN shield from arduino
previus part can be read here https://devzone...
Windows 10, Segger Embedded Studio V5.60a
nRF52833-DK (also nRF52840-DK, along with custom boards for each for later purpose)
SDK 17.1.0 S140
Hello, I'm trying to...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to change TX power of advertising but even though I have written the below...
Hi
We wan't use in our project some MODBUS sensors and I found, that Nordic Connect SDK (I use version 1.9.1) with Zephyr has support for MODBUS. I tried the samples (rtu...
