Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
I run newest nRF53 chip as of writing with 1.6.0 nRF Connect SDK from nRF Connect Toolchain manager 3.6.1 using SES 5.50c.
I use a array of 5 rx-buffers (Increased from...
Hello there,
I am getting "No devices connected" error message when trying to erase and flash to Arduino Nano 33 BLE sense board using the nRF Connect for VS Code. I also...
Hi Guys,
I am working on the nrf52840 and using SDK 17.1.0 version.
i am creating the zip file of my application code using "nrfutil pkg generate"
It give .json, ...
Hi,
On the nRF5340-DK, i'm succesfuly using the example code:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_uart/README...
Hello Support,
I just started to play with the self provisioning "Mesh-Demo" sample to get a hang of the BLE Mesh. Since I am working on the nRF52480 DK and don't have a...
Is the Common Application Framework considered ready for production use? The fact the "Common Application Framework overview" page links to "Common Application Framework preview...
This is a follow-up to a previous ticket https://devzone.nordicsemi.com/f/nordic-q-a/83842/error-when-building-configuration-for-non-secure-boards , the problem persists and...
I have connected a nRF5340 DK board which the Programmer can connect to. I then drag the two .hex files for the Heart Rate Monitor demo over to the File Memory Layout window...
I've was able to use brand new PPK2 to make test measurements few days ago and it was working fine. I've connected the unit today and software have issue recognising the device...
After reading through the nRF21540 datasheet, I have a few questions.
1. Is section 5.5 saying that even though the spec for VDD is 1.7-3.6V, VDD needs to be between 3.45...
Hello everyone,
I'm now having a problem while using nrfx_spim_xfer on nrf52840. I want to use nrfx_spim_xfer with a callback when transmitting is done.
My setup code...
Hi,
For a development evaluation, I am looking to program nRF52833 to have it interface with "IS25LQ040B" serial flash chip through SPI-1. I found lack of examples and...
I am using the "nRF5_SDK_17.0.2_d674dde" for nRF52 development.
Would like to get the SoftDevice and nRF52 device for confirmation after OTA.
1. When using the sd_ble_version_get...
I am trying to send a OnOff output cluster information to Co-ordinator when a button is pressed in the nrf52840 DK. The problem is the during the initial registration, the...
Hi.
i want to power my nrf52840 with 2 AAA batteries i connected them directly to the module. Is there any Bluetooth signal strength difference when battery voltage drop...
