Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
Hi,
My project involves an nRF52840 DK connected to an accelerometer on a breadboard, connecting to my Mac via USB-micro.
I'm editing the twi_scanner SES project so that...
Recently I received the nRF5340-DK. I tested and it was working correctly and as a test, I compile one of the ready solutions of NRF5340 of SEGGER Embedded Studio. Everything...
Hi, I am getting an error 19 which causes a reset after some time running a modified version of the ble_nus peripheral example may someone guide me on how to sort the issue...
Hi, what is the nRF52DK UART, for the nRF52832, flow control when using the ble_app_uart_pca10040_s132 example? It appears to be possible interrupt driven based on data received...
So ...
I'm still trying to get peripheral_uart running.
I'm using a nRF53 PDK (PCA 10095 - rev 0.8.0) (I've received two 0.11.0 boards, both of which died).
I'm using...
I'm using the nrfx twim driver along with Zephyr. I'm using the NRFX_TWIM_EVT_DONE to initiate a subsequent TWIM command and finding that the second command fails due to the...
Dear community,
I was working with a modified code based on an example for switching the leds on/off in a Mesh BLE network. Everything was working well until I tried to...
hello Nordic
i am using nrf52840, SDK16.0, a project build on the peripheral app_ble_blinky example
i am trying to use QSPI but the write function falls on error no...
Hello together,
I try to get the asset_tracker_v2 up and running on the thingy:91.
At the moment I get an Error from AWS_iot aws_iot: mqtt_connect, error: -116
My problem...
Hi Nordic,
I am trying to use the nrf52840 to talk with my 4G module on baud rate of 115200 , but I find it always come into error for the recving the uart data. Also it...
Hello,
I have an nRF9160 development kit and was measuring the time it takes for switching off the modem
when it has an open data connection.
I did it by sending an...
Hi,
I'm currently working on NRF52832 (Softdevice s132 6.1.0) controller and developed a firmware from light switch client to develop a mesh network and its working fine...
Hi sir,
I have downloaded the NORDIC THINGY52 SDK from the given link https://devzone.nordicsemi.com/f/nordic-q-a/51236/unable-to-compile-ses-project-in-thingy-52-sdk (As...
Hi,
What do I need to be able to FOTA when nRF Connect SDK is updated?
For example, when the SDK version is 1.6.0, can I use the changes I made to the new SDK version...
Hi, as the table register above, If I want to set Tx_Gain manually, Does MODE effect my config? (Ex, if I choose mode as 0, does the device use POUTA default to use instead...
