Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I have added lbs_service from ble_app_blinky service within ble_app_glucose example. I made changes in main.c and EMPROJECT File accordingly. I have added ble_lbs.c file in...
I need help in implementing Monitor Mode Debugging (MMD) using Segger Embedded Studio development. Can you please provide detailed help and explanation please?
Hi Devzone:
After searching through the forum I found out that nrf_fstorage_write can only make 1 to 0. So each write needs an erase operation preceding it.
But erase...
Baseline: CLI example on the 52832 with SDK v15.3
I assume the issue will be some more undocumented fix.
sdk_config.h
main.c from the CLI example (UART backend...
I was previously working on nRF51822 ble beacon, in which codes flash of hex 20006.
But i wanted to flash a code nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\experimental_ble_app_blinky...
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
Hello there, I know that softdevice supports up to 20 connections at the same time, but we need more actually.
If i implement a SPI ram to device, is there any change...
It seems NB-IOT can work on different modes according network operator condition, is there any way via AT command to interrogate the nRF91 to know the "operation mode" and...
Hello,
I just created an application that can count the number of rising edges/events on button presses using the TIMER0 peripheral configured as a COUNTER. So far it is...
I am developing an application for Android and IOS. Faced a problem when try connect nRF Connect as central (on Android) to nRF Connect as peripheral (on IOS)
...
What I need?
I should be able to perform scanning, connecting, disconnecting and accessing service from main() (in a infinite while loop) rather than interrupts. I see that...
Hello,
I'm using SDK16 with the s332-6.1.1 softdevice in ANT mode.
When I request a radio timeslot of 10 ms, that works just fine, but if I do anything longer than approx...
Hello,
we have developed a custom board using the nrf9160 SICA chip and are now modifying the bifravst cat tracker example to suite our needs.
Basicaly, it samples from...
I am trying to get my ublox module to respond to at commands, through the programming of the boron module, which is found in this link, but I don't have much idea of how...
