I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
The ble-sniffer_win_1.2_user_guide, Figure 4. Wireshark Interface, Packet Bytes window shows a 00 byte at location 0010, which corresponds to the "preamble" of the "Air Interface...
Hi
I want to declare 2 spi instances with only cs pin different.
The reason for dividing the two is because the modes are different.
The one declared above is executed...
I have used nRF5 SDK ver.16 for BLE HID digtiger.
I want to set up some feature value to HID report . Such as Contact count maximum.
I have followed keyboard example,...
I turned off the serial i n prj.conf of the mqtt_simple routine.
<prj.conf>
<nrf9160dk_nrf9160ns.overlay>
The idle current was measured at 500UA. This means that...
Hello Engineers,
We are trying to set the correct configuration between nrf9160 and nrf52840 for using the uart_pipe library. However we are still unable to communicate...
We have a Nordic development under way and I have run into a snag.
Neither of my dk board types (9160 or 52840) are recognized by jlink , no jlink drive etc….
I have personally...
So the interrupt on the nRF2401+ seems to be working inconsistently. I get interrupts sometimes and sometimes I don't.
For a context: I'm transmitting a sensor data only...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
Hi all,
I am using the nRF51822 and attach you can find the . .
I have noted that the current consumption is too hight for my scope (about 1.7mA). My idea is to 'reduce...
I tried: - changing USB cables and ports (no any improvement)
- instructions from this link devzone.nordicsemi.com/.../nrf52-dk-does-not-show-as-a-removeable-drive-in-windows...
Hi there,
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/39447/central-role-in-a-mesh-proxy-node , but perhaps slightly different in that my existing...
DFU Trigger Library (USB) is indicated that only for nRF52840 SoC. For other SoCs, can I use it after some modification of the library easily? What's the limits?
Hi !
I am on a firmware project for a nrf52832. I am using SES on Windows.
There seem to be a problem when combining buttonless DFU and NUS. When I do the services_init...
Dear devzone community,
I am currently in the process of migrating my MBED code to NRF5 SDK. My MBED code is functional and it works fine, you can find the code below: ...
There is no any Softdevice S122 listed on the page below.
https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK
We have downloaded the SDK from the same page...
