We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
We like to develop a battery powered device with small current consumption which will communicate with mobile devices over BLE. It will comunicate with mobile device...
Hello Everyone,
It is unclear to me how a soft-device operates regarding multi-tasking and event-handling. I'm assuming Nordic engineers have their own real-time operating...
Hello, i wanted to ask if NRF51 Dongle NRF51-Dongle is capable of sniffing packets from NRF52xx parts? If yes, what are the limitations, because i think that nrf52xx parts...
Below linked blogpost says,
if using a PCB antenna, the matching network should consist of one shunt component.
devzone.nordicsemi.com/.../ .
And in the reference design...
Greetings,
For my application,I need to change the nrf51's mac address.
Previously I have changed the MAC id using the following code,
static ble_gap_addr_t m_central_addr;...
Hello friends,
i am new to embedded programming and trying to learn the new things in embedded for this i am doing 1 project in which i am using mpu9250 with pwm.
is...
Hi,
I want to interface FN-M16P with nRF52 through UART. To access this module I need to send commands to perform specific actions.Is there any specific example like this...
Hello,
I am new in this community and I am trying to get started with developments using nRF52840 DK. I am using SDK 13.0 for the library and I compile my code using armgcc...
I would like to be able to leave the bootloader installed and debug an application. I have been able to use the merge tools to get the hex files all merged and generate the...
Hi, i'm currently working on a low power sensor device based on nrf52832. I want to transfer data only to bonded central devices. Priority is using static passkey, but my...
After reading a few related questions and the official tutorial, I have a guess, hoping to confirm:
If I do not need to add extra events into schedular for management purposes...
I'm doing experiments on high throughput and need to call sd_ble_gatts_hvx, but there are a lot of confusing things so it's hard to get started.
If I want to know if notify...
Hi,
I have a nRF24LE1 development kit and a starter kit. If I turn the power off and turn the power back on using the power switch S9 on the motherboard. The nRF24LE1 chip...
I am using pc-ble-driver-py to configure an nRF52832 demo board as a BLE central device. I currently have the heart_rate_collector.py example working. However, what I would...
