Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
Hello,
I am experiencing some CC register issue in Timer of nRF51822. I am trying to setup TIMER1 for 16 seconds. But I see, that when I try to write to CC registers, the...
The "Intermediate Temperature" characteristic is not coded in the ble_hts.c file.
How could I do to implement this characteristic and maintain the compliance with Nordic...
Hello,
I want to rewritte SEGGER_RTT_vprintf to use sprintf Inside (because it's already linked in my application and allow float display).
The problem is that i don...
Hi
We use the nRF51822 with s110 active. As long the s100 isn't active, we can debug, set breakpoints, stop, continue like it should work.
When activating the s110 and...
Hello,
The question is about CUSTOMER area in UICR. After locking chip wirh UICR.RBPCONF.PALL I noticed that I still able to read UICR.CUSTOMER data.
Could I enable readback...
Hi all,
Google launch uWeave Library project.
uWeave is an implementation of the Weave protocol intended for use on microcontroller based devices.First demo project is using...
Hi,
As first stage of planning our next generation of wireless sensors at my workplace, I must carefully consider which radio protocol suits us best. We don't need sub 1...
HI,
Hi,
I have been working on nRF5 Development Kit where Basic configuration is working i.e. blinky program and when I load peripheral program(PWM,UART), its also working...
Hello. I have several nRF51 devices (nRF51 Dongle, pca10031) I wish to use as BLE link between robots.
Is there any examples or tutorials that show how I can do this...