Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'm trying to build BLE driver 0.5.0 for 64bits.
I've downloaded:
MinGW 4.8.2 64bits
boost 1.56 and compiled it using address-model=64
CMake 3.4.1
Python...
Hello Nordic community:
I've read about Serialization in the nRF51 SDK doc and would like to prototype an example with it.
I saw a notice of it being removed post 7...
Hi,
Is it possible to get a more detailed description of the GPIO block than what is available in the reference manual? Specifically i'm interested in how the disconnect...
Hello Everyone,
I want to run a couple of test on the nRF51422 radio. However, how do I go about checking the firmware on these devices without the use of a motherboard...
Our device fetches fused quaternion from MPU and transmits via NRF 51822.we are using 3.7v li-ion battery.we are using Non-volatile memory.
Currently we are facing these...
I am trying to run BLE central peripheral dual role on nrf52 pca10040 with nrf_uart as service. Also, I have redbearlab BLE nano as peripheral (nrf51822 based).
I am getting...
Hi, I would like to ask that, whenever I put my function in main.c, the borad become undiscoverable.
I'm using nRF51 with ble_app_uart_s110_pca10028, and below are my function...
use nRF Toolbox APP to bonded peripheral device even disconnect and connect don't need input PIN code again, but when I turn off BT the APP lost bond information. next time...
Can the S120 work without RTC XTAL?
Iam using SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, false);
but it still hangs in the softdevice_handler_init...
Hello,
I am attempting to implement the TWI drivers from the SDK for a nrf52832 chip for a pca10040 board. I am using the twi_hw_master files to drive my TWI and insofar...
Hello.
Since i migrated from 1 to 2 SPI bus, IRQ Handler at completion is not called. Can I use 2 easy DMA SPI ?
1 bus was working fine.
here is my config
/* SPI...
Hello Nordevzone:
8.0 multilink example
I tried to use this modified handler to receive notification data from a s110 based application. The centerpiece of the handler...
Hello! I have been playing with this example and got some LEDs blink here and there, but would very much like to have UART working as well. The documentation states that ...
Hi,
I'm using the nRF51822 for a beacon and following the ble_app_beacon example (SDK 8.0.0) with some modification in order to measure the battery level through the ADC...
