Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
During my development with ANT protocol, I found that if you have a bunch of units all have one master channel. Channels will actually bump into other channels easily and...
Hi,
I'm trying to get the SPI Slave example working on my nRF51822 PCA100001 development kit.
SPI1_TWI1_IRQHandler never gets called even though the ACQUIRED and...
Looking into the schematics, I could not find any uart or spi signals on the connectors. I am good in soldering, but I would not dare connecting wires to the nrf51422... ...
Hallo everyone!
I need very low consumption when BLE working. according to S110 SDS, BLE power profile section, when BLE in idle-connect, there is Ion+Irtc+Ix32k, same...
Use the spi_master_example_with_spi_slave in SDK6 to evaluate the SPI master module but fail.
No matter use the default pin assignment or re-assign, it does not give out...
I can't find in the documentation for the IoT the usual section about requirements for the start of user code, the start of user RAM, the max stack used and whether any heap...
I would like to be able to generate DTMF tones using PWM. I am very familiar with the process, having written code to do this several times on other devices. The DTMF will...
Is it possible to use the nrf51 dongle with raspberry pi b+ ? I'm prototyping a 6LoWPAN solution where the peripheral nodes are nrf51 devices. I'd prefer the central device...
Hi, I'm not used to the bsp.c so my question could be silly. I hope you could understand.
When I used SDK 6.1, the example about button_event_handler function had a parameter...
What is the best way to transfer an array of individual values using the BLE stack?
Is it by appending all the values into one blob and sticking it into a characteristic...
I'm using
HID keyboard example (SDK 7.2), Softdevice S110 7.1 , IAR for ARM 7.1, J-Link,
on my custom board (with NordicSemi nRF51822-QFAA MCU).
/***************...
I am designing a product with the nrf8002 chip and have a question on Power consumption. Lets say I leave all the default ratio's alone and use a CR1620 battery which has...
How can I read the Bluetooth clock (piconet) which is synchronized between the master/slaves in the piconet ? I need a constant (micro second accuracy) time from when I do...
Hello,
Is it possible to know the preamble , data format and the CRC calculation to interface a radio system ( GFSK Manchester) with NRF905 ?
Thank you
