I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hello,
we noticed for one of our boards that the nRF9160 is not able to startup with a floating MISO pin on the SPI where the flash is configured in device tree (SPI1 /...
We have a custom board based on the nRF52805 that does not have a LFXO, instead relying on the RC. We are using NCS 2.6.1.
We see current spikes every 4 and 8 seconds that...
Hi,
as mentioned in the title, when using the official vscode extension (nRF Connect for VS Code) for debugging and stopping a debug session, the target state does not get...
Hi：
I have the following hardware structure：
FPGA < -- SPI -- > NRF5340 (TX) -- ! ( ESB ) ! -- NRF5340 (RX) < -- USB -- > PC
Due to the nature of my application, I need...
Hello!
I am trying to collect data from an nRF52832 device which works as a peripheral to another device nRF52832 which operates as both Central and Peripheral.
Description...
Hi,
I am downloading GPS Almanacs from U.S. Coast Guard Navigation Center web site to inject into the modem using nrf_modem_gnss_agps_write() . Below is current almanac...
Hello,
I need a way to decide on which Api to use for UARTE (configured as uart1) once in main(). I am not intending to switch between them nor to use them at the same...
I am currently working on a project to migrate to the nRF Connect SDK. We are using the NRF52840-CKAA-R7 package of the nRF52840. However, I have not been able to locate the...
I'm develping application on nrf52832 with nrf5SDK v17.0.
The connection interval is set to 12 to 16.And the conn_sup_timeout is set to 1000.
The condition happened frequently...
As I understand it, any applications using the modem libraries on the nRF9160 must be built in the non-secure domain. The MCUboot and TF-M needs to be in the secure domain...
Hi.
I need read the external voltage in input P030, and the battery backup voltage in P031.
If I read using only one channel, the P030 (AIN6 ) the value that show...
I want to send key strokes between two pic 16f887 microprocessors using the nRF24L01. I assume I can use ShockBurst to do the job. The master sends the key strokes and the...
Hello,
In the nrf5340_aduio application. I found it support 2 channels both of output(mic signal) and input(audio signal) on the USB device.
But i want to know if it can...
Hi,
I am debugging an application whth MPSL enabled and occasionally get this error:
E: SoftDevice Controller ASSERT: 48, 190
E: ***** HARD FAULT ***** E: Fault escalation...
Dear Nordic team,
I'm evaluating nRF5340 Audio DK for the use-case of broadcasting multiple streams.
Until now I've succeeded in broadcasting 4 streams (LC4 bitrate...
