We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi, We have used Thread 1.0 for our current product and using OpenThread for our next gen product. Are these two compatible with each other? In other words, can an Thread...
We need to add a custom mac address in nrf52840. I check the offical way about wirting the address in URCR. BUT it can be reflash or erase by anyone. We want find a way to...
Hi team,
I am using Segger 5.4 version and nordic SDK 16.0v for the nRF52840 microcontroller. I am working on UART peripheral to send and receive data through interrupt...
When I initialise an UARTE after an UART I get a ERROR 17 [RF_ERROR_BUSY]. Its fine if UART not initialised.
It drops out in nrfx_uarte_init at this point
To...
Hi all,
Under the latest nRF5 SDK for Thread and Zigbee v3.2.0 release, the zb_sleep_now(); will not get the device to sleep. On the light switch zigbee example, I have...
Hi,
sdk ncs v2.1.2
example :mqtt_sample
1. The mqtt client connects to the server
2. The mqtt server is faulty
3. The mqtt client cannot detect the server fault...
Hello,
I've been trying to flash the NRF5340 from my M1 Mac for a few hours now. But every time I get only the above error and that I should contact Nordic if the error...
Hi Nordic,
I need BLE mesh, central mode for TAG to pair and DFU over BLE functions, can you guide me which example in NCS v2.1.2 is better to as code base?
While interfacing LIS2DH Sensor with my nRF 52832 Board, I am getting the data in x, y and z axis. But the values of x,y and z axis remains same in each reading which is not...
Hi,
I would like to set the FICR-Address as Static Device Address in hci_uart. I know how to set this address as Public Address but can't find any suitable API to set it...
Hi,
I'm using hci_uart on nRF52840DK and configured CONFIG_BT_CTLR_PRIVACY =y among other things:
The resulting .conf shows:
But when sniffing the packets...
Trying to download the nrfutil executable file from "nRF Util" page at www.nordicsemi.com/.../nRF-Util for "Linux (x86)" fails. It is expected that this downloads a binary...
Hi, I'm designing a Zigbee router based on nRF52840. I've started from the CLI example in the SDK folder but I'm not able to provide an indication if the router is connected...
Hi,
I'm working on a legacy program (Peripheral) using nRF52833 and nRF5 SDK using SoftDevice S113.
One of the requirements of my peripheral application is that it should...
