But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I am currently using Nordic border router image as suggested by Google open thread group as i am using NRF5 SDK examples (sleepy mqttsn-publish example to be precise...
Hi team,
I am using NRF52833 DK with PCA10100 on it and s140 soft device version..
I added service data in advertising_init() function in ble_app_uart example code ...
Hi,
I have used DFU to update my application and worked normally. Now I need to update the application which has be written in NOR flash.
Firstly, I will write the application...
Hi,
We are building the custom bootloader in Rust,
Therefore want to define the non secure memory region.
Need to know exact steps to define the Non secure memory regions...
hi team,
i am using Microsoft Windows 10 Enterprise OS and Segger 5.40 version IDE.
i am using nrf52840 device in my project along with nrf5_SDK for uart peripheral check...
Hi,
In one of the example( zephyr / net / dns_resolve.h ) In this function description "dns_get_addr_info()" mentioned like below,
@details This function can be used to...
Now I've made a board using 52833 and downloaded the 's140_nrf52_7.0.1_softdevice', 'bootloader', 'settings' into 52833.
I use SD_POWER_DCDC_MODE_SET() to enable DCDC in...
Hi
I implemented in the function call in the SDK bootloader on a nRF52840 the BLE MAC address with the following function call:
The type BLE_GAP_AD_TYPE_LE_BLUETOOTH_DEVICE_ADDRESS...
hi Team,
i am using Microsoft Windows 10 Enterprise OS and segger 5.40.
i am using nrf52840 device in my project along with nrf5_SDK.
i compiled pwm code with different...
Hello, I am working on jumping from the app to the bootloader to do a firmware update from there. If I don't have any application firmware on the nRF, the DFU also works without...
I am working on nrf5340 DK using segger embedded studio. Using peripheral_uart example and i added SPI interface code. I need to integrate ICM20948 library to this application...
Hello nordic support:
Our device used nRF52840, when do RSE testing , band edge failed when channel 39 TX at 0dBm. We want to reduce ch39‘s TX power alone. Could nRF52840...
My environment is nRF52840 + nRF5 SDK 17
I have nRF52840 and LCD module(ER-TFTM101-1) connected using SPIM2.
When LCD power is on, It's fine work.
But, When LCD power...
Hi All,
My project have some problem.Below is the information of my project.
SDK => v17.1.0
IDE => SEGGER
Example code => base on ble_app_buttonless_dfu
Purpose...
Hi,
I have a BLE-project running on the nRF52840 DK. Now I made my own custom board with the nrf52811 and want to program it with the DK.
I did read I have to change some...
