But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I like to implement transfer layer on UART communication, since data error is possible on UART.
I read this " UART HCI protocol" document on Nordic SDK.
https://infocenter...
Hi all,
I think this question is generic and covers all Nordic chipsets. Anyhow, I'm planning to use a nRF52810 but I don't have a board to confirm this yet.
Question...
HI i am working with the nrf 52833 dk board using nrf connect and trying to implement SPI ,
#define SPI3_NODE DT_NODELABEL (SPI_3)
static const struct spi_dt_spec* dev_spi...
For some reason when we build a MESH enabled app we are getting a resulting hex file that includes complete file paths names. This is not occurring in our builds that do not...
For my application, most of the time, the device is asleep with the exception of sensor reading and logging every 5 minutes and occasional (and infrequent) beaconing so the...
Hello to all,
I countered the follwoing issue at starting debug phase of my project:
In details:
I think that I have to update the GDB to version >=9.
Could...
Hi,
In my application, I want to read some sensor data through SPI Communication in nrf52840, can you please provide some code or please tell me how to implement the program...
Hi,
I am using nrf connect sdk V2.0.0 and nrf5340 DK.
Using fat_fs and uart examples, I managed to get the SD card and UART work individually. For SD card, I am using...
I have build many applications using the NRF5 SDK. I have a custom service that works fine on all my applications written using NRF5.
I am now trying to port these applications...
Hi,
I want to do full modem update. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160/http_update/full_modem_update/README.html My device...
Hello,
I am working with nRF5 SDK v17.1.0 and using nRF52832DK board. While working with SAADC module I found that nrfx_saadc_sample_convert() API is taking almost 35us...
Hello, when I try to debug ncs1.9.1 using vscode in Windows, it shows that "ERROR: GDB major version should be >= 9, yours is 8; GDB could not start as expected. Bad installation...
Hi All,
I modified ble_peripheral UART example to support 4 peripheral links instead of one by referring the bel_app_multiperipheral example, I am able to connect four...
Hi everybody,
I would like to make my nrf52840dk communicating with an external ADC. As the ADC communicates only using SPI, I need to use spi_write and spi_read functions...
I have enabled UART_1 but cant seem to send any data or receive any, I have hooked it up to logic analyser and cant see any trx data coming from the board.
If i set my...
