This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I'm trying to follow the instructions to perform an OTA DFU for the Thingy 52.
https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/dfu_generating.html...
I'm using SDK 1.7.0. Here's how I have the modem code setup.
Init modem outside of thread loop
Set modem at+ comman CFUN=1 (start searching for a tower)
Once +CEREG...
hi,
when I call 'mesh_stack_device_reset()' function from the application, then the bootloader goes into infinite loop.
exactly at the point int the main() -> init_clock...
We are supplying the nRF52840 from 5 V into the VDDH pin. We are not using the USB interface, so I want to confirm what our options are for the VBUS pin. Can we leave it floating...
Hi,
I am trying to include the CMSIS-NN libraries inside the segger project. Since they are not available in the software package inside Segger Embedded Studio, I pulled...
Hello! I've been using Segger Embedded Studio (Nordic Edition) for the project in nRF Connect SDK.
So, this SDK uses CMake to build the projects. But my project involves...
Hello !
I try to understand all available crypto libraries in SDK 17.1.0 what is applicable for nRF52840 and CC310 cryptocell.
https://infocenter.nordicsemi.com/topic...
Hi,
I'm trying to implement a simple FOTA BLE with MCUBOOT following the instructions in the documentation.
I'm using Visual Studio Code NRF extensions as an IDE, and...
I have an early nrf52840-Preview-DK device that has worked fine before. When the project is revisited the board is no longer detected in any of the programs in nrf Connect...
I am building with west and then using this tutorial:
https://docs.zephyrproject.org/2.6.0/samples/subsys/usb/dfu/README.html
to create a .bin file. I then use nrfConnect...
Using NCS 1.8 and NRF5340
Right now I’m able to use the MX25U external flash that we have attached to the nRF5340, We are planning to ship our board with MCUBoot and application...
I am using v7.0.1 S132 SDK on the nRF52832 processor for BlueTooth Light coded in Segger.
I have a high speed output (50uS) to drive an external device using an internal...
My application requires to change the device name as the identification of the device. However, we found the changing the device name might not be detected by the Android...
I successfully used the OpenThread nRF52840 USB dongle support provided by the OpenThread project to implement the radio coprocessor functionality.
However, I had no success...
Hi
I have a strange error in the k_fifo-useage:
Basis is the project peripheral uart
I want to answer on specific commands send via bluetooth
static void bt_receive_cb...
