This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi developers and researchers,
I am working on a project in which multiple nodes are communicating with each other in p2p manner.
My goal is to implement a multiple access...
In the AWS IoT example I have been trying to add RSRP support (i.e. getting RSRP when sending my data packet).
I registered the handler/callback function in main after modem_info_init...
Is the mcuboot module compatible with RTT logging? I've setup mcuboot and my main application but cannot see any logging.
I have the following in both prj.conf & mcuboot...
Dear all,
I just writing a little piece of code (no softdevice, using sdk 17.00), that in theory toggle a led based on 2 compare (CC[0] and CC[1]).
The strange thing...
I am using SD 132 6.1.1 with a GATT server and when the client sends a Read Multiple Characteristic Values command, the nRF responds with Request Not Supported. I need to...
Hello,
I bought the Thingy 91 and tried to follow the instructions on the getting started page.
I started by downloading nRF connect - Programmer v 3.5.0. Then downloaded...
Hi,
I have noticed ever since I updated my nRF9160 DK modem firmware to the latest version v1.2.0 frequent registration dropouts and very sluggish MQTT performance.
My...
Hi, I recently bought a Nordic Thingy 52 and it looks great ! It looks like there is a decent mic and speaker on the device and I was intrigued if the device could act as...
Hello,
I am trying to do communication with external module using UART0. But when I connect pin P0.28 (RX of UART0) to external module to receive the data, there is no data...
Hello,
I am working with SPI on the Nordic nrf9160. I am currently on the DK.
The board I need to interface through SPI works at 25MHz (minimal frequency) and I would...
Hi everyone,
I know that I can configure the resolution of app_timer by adjusting the prescaler form sdk_config.h
However, what is the practical purpose of prescaler...
Hello,
I have created an empty mbed-os program from Mbed Studio, add sum LED on off logic and compiled against nrf52840dk board. After generating hex file, I upload the...
Hello,
I have created an empty mbed-os program from Mbed Studio, add sum LED on off logic and compiled against nrf51dk board. After generating hex file, I upload the program...
Hi, I want to write 510 bytes of data to my BLE Characteristics, so I set parameters ble_gatts_attr_t max_len as 510 and its variable length attribute. Also I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello,
I just bought a new nRF5340 PDK and wanted to learn it a little bit. I searched on the internet and found very useful information about nRF53 architecture.
But...
