But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello!
I am trying to interface with some old hardware that communicates over a single data pin. I need to take in varying 32-bit packets and output the data that translates...
Hi all,
The chip we used is nRf52832, the version of SDK I used is nRF5_SDK_15.2.0_9412b96.
The problem is when I pair to windows 10, sometimes PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
Hi,
I am using i2c driver available with zephr as i2c master. This is working fine.
I want to change the pins to P0.02 for SCL and P0.03 for SDA. I see multiple questions...
Hello,
I am looking into the peer manager and the LESC module and have some question regarding what is possible to do with this.
Is it possible to manage the private...
Hi,
I am updating SDK version from 15.0 to 17. We are using nrf52840.
I would like to know if these are necessary to add, as they were added in some examples, and if so...
Hi,
i have a problem when using the ble_uart connected to Raspberry-pie withe Bluez.
after 40 seconds the connection is lost.
tried to use several examples, but most...
Hello Community I am starter in nrf51822 i want to know if anybody has code for interfacing with ADS1115 since i didn't got any of the post which would be helpful, please...
Hello,
Is there a particular test Nordic recommends to screen for latent failures in the BLE circuit? If one has access to an Anritsu MT8852B tester with Direct-Test-Mode...
Hi,
I am updating SDK version from 15.0 to 17.0.
In many examples PM_FLASH_BUFFERS was changed from 2 to 4? What is the meaning of this change? We have one peer always...
While exploring documentaion and trying to learn more about the DFU (and bootloader settings), I found info on how to generate the bootloader settings , which also explains...
I want to measure voltages at all 8 channels but when I am enabling all channels its sending the values once only and after that its not sending anything, my requirement is...
Hi,
We are aware that i2s internally includes hardware double buffering to ensure that the audio is continuous.
Is there any way by which we can avoid double buffering...
Hello,
I developed board with NRF9160 chip and I am facing issue with "at_cmd: Failed to open AT socket (err:-12)", i am not able to communicate with modem. It is not...
Hi
Can I not modify the param the radio project example,and let it run on IEEE802.15.4-2006?
and the demo example run on 2.4GHZ?
I modified two params:
NRF_RADIO-...
Hello,
I'm using nRF52480 Dongle. I executed an Erase All from SEGGER Embedded Studio. My project still works but the LEDs are not blinking anymore. The only way I can have...
