Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
Hei,
I am following the Install the toolchain section and after running
choco install python
the step does not verify because it does not find pip3.
'pip3' is not...
One of our resellers is requesting a classification code for the RF protocol. We use a Proprietary RF protocol based on ESB (Enhanced Shockburst). Is there an IEEE or a different...
I am experimenting with trying to improve the current range of gzll nRF52840 dongle to dongle (which is not that far from what I need). I am developing using nRF5_SDK_15.2...
Hi,
The top level page nRF5 SDK Documentation Library page ( https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/index ) contains a link to "S140 SoftDevice...
Hi,
I am trying to implement the DFU example from Mesh 3.1.0SDK and 15.2.0 SDK. I am following the process mentioned here .
I am using a MacOS for development.
I am...
Hi
I am using device manager and store connected devices value on next advertise device should be broadcast as bonded
static uint32_t device_manager_evt_handler(dm_handle_t...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
I am making a BLE device that uses 7 ADC inputs. Most of the inputs need to read at 1hz or so. Two of these inputs are of interest
The first is a heart-rate signal that...
Hi,
I want to measure ADC for 3.3V
Using formula
RESULT = [V(P) – V(N) ] * GAIN/REFERENCE * 2 (RESOLUTION - m)
Rearranging eqn:
Vin = ( RESULT*REFERENCE)/(2 (RESOLUTION...
Hi,
Does every nrf9160 chip have its unique chip ID? if yes, is it the one which can be read by the AT command AT+CGSN ? and can it be used as the board serial number? ...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
We are using nRf52840 chip with Nordic SDK 15.0 version using SES IDE. When we use debug mode in build configurations program is not working or not debugging got error as...
