At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello,
I work on module BLE LAIRD BL652 and I'm a BLE peripheral. I have tried to make a BASIC program for advertising while in a connection but without success.
As...
Hi,
i am creating a new project iar workbench 7.8 with SDK V8.1.0 and softdevice V8.0.0 using custom board nrf51822 ic revision 3 (QFAAH00),clock source as "NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
Hello Sir,
I am designing PCB using nRF52832 SoC it is very small and operated on AA battery source.
So please recommend me for reverse battery voltage protection diode...
Hi Guys,
Me again. I was thinking someone could provide some suggestions on my understanding of the BLE connection ( porfile, GATT, characteristic,value, etc...)
I finished...
I had successfully write a structure data to fds. After which, I would like to update the same file and record key with new values of a structure. After updating, I will read...
Imagine I have developed a MESH made up of 50 Relay Nodes and I say only Relay Nodes because any of them must be able to relay and also able to initiate a message. In my application...
Hi,
I am making a GPS tracking system using NRF51822-QFAC. I am using 2 UARTs, one of the (external) GPRS IC and one for (external) RS485 communication.
The UART peripheral...
HI,
I tried to compile Thingy v2.1.0 with keil. And sereval file are missing.
Actually i work with your SDK 14.0.0, i find so many missing file, but not all.
Can...
Hi,
I am currently testing with a USB MSC example .
FATFS_QSPI is disabled because the file system is not used,
Subclass has also been modified to 0x06 -> 0xFF.
...
Hi,
I am implementing experimental_bootloader_secure_usb code example on PDK PCA10056 V0.9.2 using Sdk v14.0 and also tested with Sdk v14.2 but in both cases Windows 10...
With SD140 v6.0.0.6 having been released, will an accompanying example project that demonstrates simultaneous use of BLE and USB be released? Will this be included in the...
Dear devzone,
I am currently merging the Mesh SDK into the normal SDK to run BLE & BL mesh concurrently.
Followed multiple guides to get it working, at this moment I am...
I use nrf52832 development kit,nRF5 SDK for homekit.
Now I have read and write to UUID, want to realize how to handle the notification operation, and call what API?What are...
I enter to bootloader via my app by UART command:
err_code = sd_power_gpregret_clr(0, 0xffffffff);
APP_ERROR_CHECK(err_code);
err_code = sd_power_gpregret_set(0, 0xB1...
I know nothing about bluetooth
like ble_app_uart , uart to where?how to use this uart?
like ble_app_alert_notification, alert? beep? vibrator?
any tutorial of develop...
