Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hello,
I am designing a custom board with NRF52832 IC. I followed all PCB consideration suggested by Nordic.
This blog suggests, If using a PCB antenna, the matching network...
This question is similar to this thread:
devzone.nordicsemi.com/.../
However it was framed differently and didn't really clear anything up for me.
Say my application...
Hello,
I have an application that has to be ported to the newer Softdevice version. I've already ported my application to the SDK 13 and tested it with the new Softdevice...
The NVMC documentation states the CPU is halted while the NVMC is writing or erasing flash. If the CPU is halted, then interrupts shouldn't need to be disabled during flash...
blog.bluetooth.com/management-of-devices-bluetooth-mesh-network
The Provisioning Protocol
During provisioning, the Provisioner and the Device to be provisioned communicate...
as this screenshots show, i add some headers to nRF_Libraries, and add the directory of the folder nRF_Libraries to Options for targets /c++/include paths,but after building...
Hi,
I am trying to use the SAADC via ble when noridc is connecting with other device and adding value to advartasing. This is my code but i've got some problems.
1)...
I am modifying the bootloader_secure_ble code to receive a serial number via BLE and store it in flash. However, whenever I call nrf_dfu_flash_store or nrf_dfu_flash_erase...
Hi,
We are currently working on one project.
Initially, the nRF52840 & S140 (v5.0.0-2) & SDK14.0
examples \ ble_central \ ble_app_multilink_central Based on the example...
Hi Team,
I am using sdk12.2.2 and nrf52. I want to use one gpio to detect button state & have to operation on that event.
I used one method to configure(code snippet...
Following the guide found at : file:///C:/Github/STIWHN/SDK_thingy52/thingy_sdk_v2.1.0/documentation/firmware_compile.html#compile_gcc
I still getting errors trying to...
Hello,
For the softdevice update, is it the responsibility of the bootloader to make sure, that the softdevice was copied correctly?
If for example the bootloader calls...
Hi,
When i use FreeRTOS tasks with priorities 2,3,4,5 what i need to #define for XXX_CONFIG_IRQ_PRIORITY of SPI,SAADC and GPIOTE at the file sdk_config.h
Thanks
Hello, I use nrf51822 , sdk 8.0.0, s110
I defined advertise interval and timeout
#define APP_ADV_INTERVAL 320
#define APP_ADV_TIMEOUT_IN_SECONDS 3
Also, I write...
Hey Nordic Devzone,
I am really new to Nordic and am still a student in embedded software engineering. So first some background information.
I have 6x nRF52840 and 5x...