Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
It seems that many people use GCC toolchain (with "high" setup effort) for utilizing SDK in C++ development.
It should however be possible also on Keil with less setup effort...
I am currently using version 'NRF D 8001 1429SH' as printed on the nrf8001 IC
I have already managed to successfully bond with an android phone and completed the ReadDynamicData...
I am trying to migrate from using an earlier chip, the 8001 over to nrf52832 because we want to utilize new ble 4.1 features. The issue is we have another micro that was a...
Hello, i did not find any solves and i want to ask you are , how can i change my data in advert packet? I tried to do it from TIMER interrupt without advert time out and with...
I've been trying to import this NRF51 Eclipse project for a few days now, but no success.
github.com/.../HomeKit
I've tried to closely follow the steps outlined in this...
Hi all,
I have a PCA10040 board and want to try the BLE examples provided in nRF5_SDK_11.0.0-2.alpha folder. However, there is always a problem when flash BLE hex files...
Hello,
I have a capricious component on my TWI bus, and sometimes my nRF52 do an infinite loop in file nrf_drv_twi.c
in this loop
while (!nrf_twim_event_check(p_twim...
Trying to connect nRF52-DK with Nexus 5 (Android 6.0.1) SDK 11 NFC HRM example
But can see this device in paired devices list. Next time i do it it never attempts to...
hi,
i have a timer which is being called each second. when i give timeout less then 1 second then the code executes properly and goes to event handler. but when the timeout...
Can you tell me how to integrate this library so that my code works with it? I'm new to using both these OLEDs and Nordic Semiconductor based devices. THanks
I'm trying to write a firmware for PCA10001, which works like a bootloader. In other words, it can download some data into the Flash. To avoid conflicting with the existed...
Hi thank for reading with your kindness
I used keil with nrfready_desktop_2_/* files
when I clicked "Start/Stop Debug Session" with simulator in debugging session, ...
HI,ALL
i notice that the buttons_leds_init is initiating the bsp function.
just like LED and Buttons.
uint32_t err_code = bsp_init(BSP_INIT_LED | BSP_INIT_BUTTONS,...
I recently purchased nrf51-DK. I was going through a getting started document which said to update the firmware on the board. After updating it the boards just keep disconnecting...
Hi:
There is a worried question around me.
when i put my product and phone in a firm place after the product connect with APP of phone.
I find that there are lots of...
