Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi,
I´m using a Fanstel BC40M board with a nRF5340 on board as a peripheral device.
Being connected to a central, it triggers some tasks in the peripheral. The peripheral...
Hello All,
I have nrf9610 Develoment Kit on my side:
mfw_nrf9160_1.3.5
Using nrfutil-device core version: 7.13.0
Using nrfutil-device version: 2.1.1
...
Hi Q&A
Recently, the Bluetooth communication protocol (nrf52833) was added to the ESB, both can communicate normally, but there is a problem when switching between the two...
Hiii,
I have added BLE from peripheral_hids_keyboard to Peripherial_Uart,and now my PC and mobile (Android) can connect with DK(nrf52833) and can regard it as a HID,but...
Hi experts,
I am in the process of upgrading the projects based on nRF52SDK to nRF connect SDK. Previously, we used to store the entire nRF52 SDK along with our custom code...
Hi all,
Currently our team is trying to implement a bluetooth mesh sensor network. We have started testing and experimenting with the mesh interface by trying to follow...
i Used a nrf52840 DK board and zephyr sdk v2.6.0. I'm start the ble advertisement and configure the gpio interrupt on sw1 in low mode flag GPIO_INT_LEVEL_INACTIVE (Low level...
Hi, I tested the TCP client AT command in nrf9160DK, I flashed the ncs v2.5.1 example of serial_lte_modem firmware on the board.
I send the command as below list:
AT#XSOCKET...
Hello
We are using nrf5340 in the new project. PCB design was made. We are currently waiting for the typesetting process to be completed. There is no Jlink on the designed...
Hello,
I am creating a new project that uses the nRF52810 as my controller, and during the development stage, I am using the PCA10040 nRF52832 development board. (I read...
I've got a custom board that puts UART_TX on P0.14 and UART_RX on P0.15, with no RTS or CTS signals. I've got a USB to UART cable that I've plugged in, and I know at the very...
Hello, I am working on an application where large amount of data are being stored onto a NOR flash. The flash is a W25Q02JV with 2Gb of storage, running little FS. My application...
During my test of the nrf5340 audio application which in the V2.6.0 SDK , Because of i need to store at least 13K data to the flash.
But when i build the project, i found...
I am using FATFS file system to store data in a .json file using sd card. When I debugged the code I got FR_INVALID_NAME issue in home.json file name. I am not very sure though...
