Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application (in BIS mode).
I also have my own customized board, based on Raytac MDBT53v, for...
I have a nRF9160 custom board. I am using 2 UARTs (UART0 and UART2). I need to have an RX interrupt on both UARTs. I have identical setups and configuration and code. The...
We are using PC-BLE-DRIVER-JS for our central and zephyr in our peripheral (833). The central bonded with the peripheral only when the id (IRK) param in our central is set...
Hi all!
Hopefully this doesn't come off as too much of an ignorant question, but I'm having a hard time understanding the pinout of the Thingy 91 since I can't map where...
I´m trying to design a compact circuit for the NRF91, since i have limited space i´m planning to do a board stackup with the antenna board on top. Right now my board is 50mm...
I am working on an application where I am using 3 SAADC channels all with the same reference pin.
Upon startup, I will call app_sensor_init() to initialize my SAADC, timer...
The Commissioning and Characterization note for the nRF700x series ( https://infocenter.nordicsemi.com/pdf/nan_043.pdf ) says in section 2.1.2
However I have been unable...
Hi! We are considering moving from nRF9160 to nRF9161 on our custom board.
We are currently running modem FW 1.3.1 and nRF Connect SDK 2.0.2 on the 9160. However, we find...
Hello,
I am looking to conduct a test to simulate a Zigbee device using nrf52840 in the Zigbee:shell sample. This involves modifying the manufacturer ID and model ID. If...
I need a clarification about the update of gpiote driver. I've passed from the NCS 2.5.1 to the 2.6.1 and now I have issues in the configuration of my ppi infrastructure....
Hi,
I have a peripheral which is sending data to a central via the NUS service. Everything works as expected until the central is removed (e.g. power failure)
The problem...
Hi, basically I want to expose my firmware's version through the GATT DIS (Device Information Service) to client applications.
I have gone through:
the VERSION file...
The link provided as part of the webinar to download the PPT is not working, So could you please with PPT
Following is the webinar link
https://www.youtube.com/watch...
I develop using Apple M3 paired with VS Code with nrf extension. The development board I use is NRF52840DK. When using JLink firmware with version number JLink_V796b, the...
Hello,
I just recieved my nRF5340 DK and was going through the "Getting Started with nRF5340 DK Guide" ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/gsg_guides...
