Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
I am trying to write and code of aes encryption and decryption using ccm mode for my application on nrf52832 controller. I have went through some example on Github for the...
I am developing UARTE using nRF52840.I use a wire to connect the TX and RX pins together, and send something out the TX.
However, RX did not receive any data, and the interrupt...
Hi,
I have the separate working codes for the TWI0 and the SPI1. However, when I combine them, it doesn't work: sometimes it takes forever waiting for the NRF_DRV_TWI_EVT_DONE...
Hello, I'm trying to figure out how to work correctly with timer 0 in the nRF24LE1 microcontroller.
1)The Cclk frequency in my case is 16 MHz
2)Given a fixed limit of...
We are new to Nordic and have been making great progress with our nrf52840DK board and successfully running many of the Nordic SDK examples. We can't seem to find a single...
hi
the saw filter used in thingy:91 is : SAFFB2G45MA0F0A which is obsolete end of life now
suggest me another saw filter for ble application chip antenna implementations...
Hi all. I am using nRF5 SDK 15.0.0 and the S140 SoftDevice v6.0.0 to develop on an nRF52840. Due to software infrastructure constraints, I am unable to implement DFU using...
Hello,
I have a use case where I need to use UART_RTS and UART_CTS as GPIO for toggling the led. I also want to use the other two pins UART_TX and UART_RX for handling UART...
I have created an application that initiates a timer for 30 seconds and when it expires it calls an expiry function that switches the system off, if no button is pressed since...
If you try to write a program on a board with nRF5340 installed, an error will occur.
I can write to other boards using the same J-Link, so I don't think it's a J-Link problem...
Hello all,
I have scoured the devzone and other blogspots to find an answer to this but so far have come up short.
in short i want to use one NRF552-DK with the adafruit...
Hi,
I made DFU procedure with a distributor (nRF52840 DK) and one target (nRF52840 dongle): procedure completed successfully in approximately 45min
Then I made DFU procedure...
Hello,
I have a problem with a custom board with a nRF9161. I am trying to connect the board with the nRF9161 to the LTE or NBIOT network, and the board doesn't seem to...
Hi,
We've got a board with a fairly limited power supply in production and it's expected to brown out under certain conditions. As such, I need to verify the reset loop...
Hi community,
ncs-2.6.0 I'm using.
I'm trying to enable bmi270 as I enabled adxl362(is already working), both are connected with SPI.
but it shows me this kind of...
