Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
My team is still using version 1.9.1, which is no longer available in the updated toolchain manager. Installing manually is too error prone and usually breaks anyway as python...
Could someone please tell me if external series resistors are necessary for D+ and D- for USB 2.0? I've seen some comments here that they aren't necessary and may cause problems...
Hello,
I was trying to run TFLM custom code on Thingy:53 device and while building I have faced these warnings.
1. Could you please help me to understand Why I am...
These are the details of my system:
Ubuntu 20.04.5 LTS
nRF Connect for Desktop v3.12.0
Toolchain Manager v1.2.1
Visual Studio Code 1.73.1
NCS 2.1.2
If I start...
I am working with ncs version 2.1.0 in visual studio code, for reference.
I have been trying to get any of the SPI channels set up on the 5340dk with no luck. I've come...
Hello everyone,
We're trying to create an application that has 2 modes, one is running our regular application and upon a special command, it switches to a "DFU" (via device...
I'm testing the thingy91 with asset tracker v2.
I managed to build, flash and get the thingy 91 to send data to the nrf cloud platform perfectly, but as i've seen in the...
Hello,
I am using nRF52840 DK, and SDK version 17.1.0
I dynamically and explicitly request and restart HFCLK clock source after I released HFCLK clock source while...
I am encountering an unusual behavior when I stop/start app_timers from the GPIOTE IRQ. I am implementing a debounce procedure from a GPIO interrupt .I find the timer callback...
I'm using nRF Connect SDK v2.1.2 with Visual Studio Code and a nrf52840DK.
I have implemented this app (OpenThread CoProcessor NCP from Zephyr) and it is working correctly...
Hello again!
I have configured and initialised the Thread API from the Thread/Zigbee client publisher example, and receive no errors or warnings when attempting to send...
Hi,
Is there a possibility to change the COM port number of the nRF52840 USB dongle manually?
I already looked in the device manager under the port tab, but couldn't...
Hi all, I have a prototype device app I'm going to "deploy" in a remote location with an nrf52840 dongle. Initially ble via special shell commands added to nrf/samples/bluetooth...
Hi all,
I'm new to embedded programing with Nordic I'm using the evaluation of Fanstel EV-BC 805M. I was trying to program the basic program for blinky led, however by the...
