Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello I don't see any change in RSSI with different TX power values under Zephyr. 1.9.1
It used to work with Nordic SDK 3.2.0 (see table below) The HCI API in Zephyr that...
On nRF5340, we are using Thread communication, Wifi and LTE-M module.
User can change the interface board, between Wifi or LTE-M module on the same UART bus.
& uart0...
I changed the central UART example to work with a demo I'm writing. I removed the hardware UART part and only send messages to a peripheral. What I do is I measure different...
I'm using an nRF52840 and SDKv17.1.
I have an active-high interrupt source connected to a GPIO pin. I understand that a GPIO should be able to wake up a system from system...
I think the nRF Connect toolchain is missing the right driver for the CLI app on the USB dongle, or the CLI is not setting up the USB interface with the right VIN.
When...
Hi,
Trying to run one of the Acconneer samples I get the errors below:
service_handle = acc_service_create(envelope_configuration); returns a NULL handle, all up to this...
I'm trying to connect my nrf52840 to the App but I have error message and impossible to continue ...
Here the log of the app standalone :
2022-10-07T21:50:58.341Z INFO...
During the software testing process, our device is connected to the rtt viewer for testing. At present, a problem is found during the test: sometimes the test engineer suddenly...
Can a single sdk_config file that has all possible macros definitions to use with an SDK
(1) be provided ?
(2) so that an identical sdk_config file be inserted in all...
Hello,
There is a missing #ifdef check on the following line of SDK Zephyr at the latest version v3.1.99-ncs1:
https://github.com/nrfconnect/sdk-zephyr/blob/98bc3a7a6b3917ce5a058e7a7271d3036edffb88...
I changed Kconfig of u-blox board template and something is going wrong in create_nordic_project.py when I tried to create project in Segger Embedded Studio from changed template...
hi support team,
there is one question feedback from customer, device（832）is sending data to mobile device, however this connection is disconnected （however there would...
Hello,
very early evaluation question, the 52832 has NFC-A. Is a mobile phone capable of reading from this device (some arbitrary user data) ? Now I've started looking into...
