But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hallo, hope you are having a good time.
I am using nRF SDK 17.02 and uses SES as an IDE.
Soft device S140 7.2.0
I have an application running which act as a central...
Hello,
I would like to know if it is possible to provide an example based on the lte_ble_gateway sample for writing and reading the characteristic!
I changed the example...
Hi Nordic,
nrf5 sdk 15.2.0, nrf52832.
I am testing the UARTE with the example experimental_libuarte. I changed two functions like below:
1. nrf_libuarte_tx(): m_tx_len...
Hi,
I am using vscode with nrf pulgin for development. after adding mcuboot to the project, Which hex file name to be used for programming through nrf programmer?
I call the k_msgq_get function to get a msg,however it return -11,which is not explain in document.
code:
Raw_data raw_data ;
int rr = k_msgq_get (& df_packet_msgq...
Hello,
I am working with the 9160DK and the AWS IoT sample in NRF Connect 1.8.0. The app is usually able to connect to LTE but sometimes it gets stuck and never connects...
Hi,
I am testing simple code on various project on my custom board. I have 4 Leds on custom board.
for (int i=0;i<50;i++) { nrf_gpio_cfg_output(i); }
I have LED connected...
Hi, We are attempting moving our BLE security from mitm to lesc+mitm, and have a few questions on the matter:
Is it "good practice" to change the security of the characteristics...
Hi,
I have developed a device with a smartphone controller. I can transmit and receive commands to the device using the ble_app_uart instance. I want to send data from device...
Hi Friends,
I am not yet familiar with NFC and have a question about using NFC with the nRF52.
If I understood it correctly the nRF52 is a "listening device" i.e. it cannot...
This previous case is an example of what i am trying to do.Reconfifure the radio parameters.
Using example code does not work for me. the DUT has other aspects that need...
Hi Nordic,
1.I am running (C:\ncs\v2.1.0-rc2\zephyr\samples\drivers\uart\echo_bot) but i need to change baud rate within program
2. I Can Change my baud rate using overlay...
Hi All,
I modified ble_app_uart_c code to create multiple central connections instead of single central connection.
Here I am facing problem, once my central device...
Hi all
For the nRF52832, there existed diagrams for "GPIO drive strength vs Voltage" and "Max sink current vs Voltage" in the product specification (PS V1.8, figure 25 ...
Hi, as the title states, we are exploring the possibility of building a product that utilises dynamic multiprotocol to be a BLE Peripheral as well as a Thread SSED concurrently...
