I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
i2c_recover_bus is used to re-sync slave devices on the i2c bus when they may be out of sync due to a reboot or other event.
i2c_recover_bus is currently not causing the...
Hi,
I'm mid-way through designing a custom board using the nRF52840. As I am space and height constrained I need to use the Tag Connect style connector used on the nRF52840...
We want to be able to manually send Friendship requests from LPN or to change request interval runtime.
It was possible to send requests manually using nRF5 Mesh SDK, however...
Hi guys;
I try to read and write the data without connecting nRF52832 .is there possible to do? Then is it correct or not? if it's wrong means give me the possible solutions...
I have a DK board with nRF52832 that I've been using several months with no problems.
Today I wanted to try an experiment and did some modifications to the startup ASM...
Hi,
Our setup is a new design with SDK 17.1.0 and it is expected to support DFU over BLE. We are using the nRF52832 SoC.
I am trying to understand the role that is being...
Hi,
We are having an issue modifying the blinky_pwm example for our needs. We have made a devicetree overlay file setting the pwms of &pwm_led0 to 28 and pwm0's ch0-pin...
I would like to use nrfjprog to erase nRF52832 device. But it failed with "An unknown error". The nRF52832 device connect to laptop through J-Link USB interface.
D:\Nordic...
Agenda : Use crypto features like AES-CBC, AES-CCM, RSA, ECC, etc. in secure environment (i.e. trustzone with SPM). Also, to use HUK, KMU for secure key generation and storage...
Hi All, I am migrating some applications (each with multiple custom board) from nCS1.5.1 + nCS1.9.1 to nCS2.0.0 I also noticed that in nCS2.0.0 the build output folder is...
Hi,
Depending on how the nRF5 SDK is configured, the BLE address may change once in the bootloader (it's incremented). This happens in the gap_address_change() function...
Hi Everyone,
I am trying to do OTA on NRF52833. In my previous project I was able to do OTA on NRF52840. The memory requirements for the project were as follows:-
Memory...
Hi, I'm trying to configure my VScode project for the nrf5340dk using the nrfconnect sdk to be more version control friendly and require less interactions to set it up. I...
hi..... everyone
I want to send the data from one node to particular node and that same data should want to print in termite using uart . so i checked the ble_uart coexist...
Hi all,
I'm trying to use the nRF52840-DK board to interface with the MAX31865 RTD-to-Digital Converter. I've adapted the MAX31865 C++ library to C and replaced the Arduino...
