Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello,
we are using the "AT%CCLK?" at it works very nice.
but now for the challange... since the modem is synchronized with the LTE network and sends on the designated...
I notice a problem with the MCUboot Hello World example.
I followed the steps mentioned in https://www.mcuboot.com/documentation/readme-zephyr/ That is, build the MCUBoot...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 I could build with NCS v1.9.1 but I cannot build with NCS2.0
[Build log] In file included from C:/NCS200/v2.0.0/zephyr/include...
I have an Ellisys Bluetooth Explorer 400 sniffer and am trying to sniff the ISO audio data between nrf5340 ADK boards. I enabled CONFIG_BT_LOG_SNIFFER_INFO, CONFIG_BT_DEBUG_KEYS...
Hi there. I am trying to utilize both the network core and the application core to perform two separate tasks at the same time. I have looked through some of the sample projects...
Hi, I need to setup a vendor specific class USB device driver. The driver shall present the following data endpoint:
0x84 for Bulk IN endpoint 0x03 for Bulk OUT endpoint...
SEGGER Embedded Studio for ARM can't connect to nRF52832 device. But J-Link RTT Viewer can connect to nRF52832 device. The following is log messages of J-Link RTT Viewer....
Hi there,
I am currently developing on the nRF5340DK and am doing some very processor-intensive work (@ 128MHz) on data read from the QSPI bus. I would like to set up non...
Hi, I have been trying to build an example of console usb example and then build it for thingy91_nrf9160_ns but got an error :
I have been trying this code several weeks...
Hi, with appropriate pm_static.yml and dts.overlay we managed to setup a LittleFS instance over external flash. However this broke the Settings storage subsystem the BLE stuff...
hi support team,
for our sdk17.0.2 demo hid_keyboard, i tested it and using IOS mobile to pair with our 840dk or 832dk
find out after lots of reset the keyboard device...
I am developing an application that uses nRF52840 wake on NFC, and spends most of its time in system OFF state with NFC wake enabled.
Per the nRF52840 Product Specification...
On the NRF52840 dongle am building a protocol on USB CDC ACM.
Using app_usbd_cdc_acm_read to read one byte at a time works perfectly.
However, I can seem to make app_usbd_cdc_acm_read_any...
Hi,
I am developing a wireless product in which i want to use nRF52 in ESB mode.
The product is battery powered and should be sleep mode.
What i have decided to do is...
