Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi ,
I want to use a pin on board, which is not used or initialized in dts file . my requirement is that I want to initialize that pin before booting process. ( that pin...
Hi,
I am using the :
bt_scan_filter_add (BT_SCAN_FILTER_TYPE_MANUFACTURER_DATA, &mfgData);
scan-filter works well.
However, keeping everything same, if setting...
Hi,
I have been working on the display from JDI LPM027M128C with the nrf52840 development kit. By consulting the datasheet of the display, it seems to work with the spi...
hi :
can you help me to solve this problem. The path of the example is bellow：
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Fexamples.html&cp...
Hello,
I am trying to work with the MCUBoot bootloader in my project. I was able to configure and build my project and it appears to run properly when I flash it to the...
I have a nrF52840-DK and would like to try some precompiled test, but I got an error when copying a hex file to it. The error message is that The currently active SWD interface...
We need to store a .fw firmware (or any binary/hex) image for an external device hanging off the nRF52833 in internal flash. What is the best way to integrate the image into...
Hi
after install sdk of nordic( Installing manually — nRF Connect SDK 1.9.99 documentation (nordicsemi.com) ) on ubuntu 20.04 LTS, when run EmbeddedStudio, i got the message...
Hello all,
for the last few weeks I am trying to workout the i2c protocol with the sensor and the nrf52dk , so far none of the solution that I have considered work. More...
Hi,
I upgraded to the newest SDK and now our SPI Code (RFID Reader) is not working anymore. Is there something that changed with parameters or anything else? If I step back...
Hi there,
We are intending on using the serial LTE Modem example on our nrf9160 with MQTT. What version of MQTT is supported on this example?
Kind regards,
Frikkie
Hi,
I have been using I2C code for almost a year to talk to a variety of sensors with complete success. Typically, we have used a Nordic BL654 module that includes an nRF52840...
I'm getting a strange amount of error when trying to measure the battery for a custom PCB based on the nrf9160.
Details
My VCC_IO is 1.8V
My max battery voltage is...
