I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi everyone,
I am looking the schematic of nRF52840 (PCA10056) and I am a bit confused with the Power Sources (sheet 7 of 7).
There are three load switches that prioritize...
Hello,
My project:
- I have a low consumption project width BLE. - I'm using internal LF clock (I know it's better to use an external) - I use the Beacon example project...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hello,
I've started to develop with the nRF Connect VSCode extension and enjoying it a lot. However, I've noticed when I share a project the build configuration doesn...
Hi,
I observed what appears to be the same issue as https://devzone.nordicsemi.com/f/nordic-q-a/51337/nrf9160-infinite-nrf_connect-blocking-behavior-post-lte-psm-wakeup...
Hi,
I'm trying to write data to a characteristic. This is a BLE led driver. I can successfully send 5 writes and then it stucks. All the 5 sends succeed - I can see the...
Hi
I need to Send one character from mobile. based on the character I need to glow the LEDs which is placed on DK. How can I achieve this is there any sample available for...
Dear forum,
We capture audio via PCM (10kHz, 8bit => rendering a raw rate of 80kBaud) on a BM833 and would like to transmit the data (one way) to a paired device using either...
Hi,
NCS1.9.1, VSCode, nRF5340DK,
Without external flash memory and not use mx25r6435f which on DK,
how does MCU store data (such as a series of serial numbers)?
and...
hi ，i want write flash by jlink，eg：write val 0xaaffffff to addr 0x76000, only write 4byte.
but when i write, err "flash not erase" occurred，
I don't want to erase this...
I try to onewire communication for DHT11 but I couldn't it . I decided uart instead of onewire. The different microprocessor will read the sensor data and send it via uart...
Hi,
I'm trying to combine OpenThread, MCUBoot and LittleFS in a sample in nRF Connect SDK v1.5.1, but I'm getting the following error:
I have checked the file, and it...
Hello NRF Buddies,
My project is based on NRF51822 with SDK version 12.2.0. I am working with Keil till now and planning to migrate to the Segger Embedded Studio.
With...
I am not sure what I am missing in this. This is a custom board so there is no other circuitry on this pin other than a pad to monitor the signal changes with.
When...
Hello!
Regarding the CRC on the nrf52840 the specifications make it clear that the maximum length of the CRC is 3 bytes, We are working on an industrial communication protocol...
