Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
I'm trying to get my nrf9160dk board up and running with the nrfcloud service. However, when I input the SIM ICCID and PUK, the nrfcloud site starts it's "working" process...
Good day
After flashing a sample to my thingy 91 I seem to have lost the Jlink connection. All im picking up is the UART via nRF connect Programmer. Is there a Bin file...
Hello Sir/Mam;
I am new in nordic environment so i need your valuable guidance . i want to read a sensor data using Uart . I have successfully do same thing on Arduino board...
Hi,
I had previously asked about SPI interfacing of the RFID card reader and I was successful in creating a custom application using connect SDK 1.5.1.
But according to...
I currently have an application with B0->SPM->MCUBOOT->APP and am looking for an example of how to upgrade MCUBOOT itself over the air from a file downloaded from some server...
We're using a nRF52DK and the Nordic-Programmer-App to flash our firmware on our custom boards. After upgrading to Programmer v2.3.3 I'm getting the Error-Message "Part of...
Hi,
I am able to successfully build and flash applications from the CLI.
When setting up the nRF Connect VS Code extension, I run into an issue where it can't seem to...
Hello, I am trying to use the spi_flash sample project with a laird bl654 dvk. When I run the project however, dev->state->init_res = 19 and will not run for me. It recognizes...
Hi,
I have been trying for several days to modify the ble_app_uart project on the peripheral side to use the BLE Long Range, unsuccessfully. I use the NRF52833-DK with...
Hello, sir.
I want to use the i2c bit bagging method, thus I used the DeviceDownloadnRF5 SDK 17.1.0 ddde560nRF5 SDK 17.1.0 ddde560componentsdrivers nRF5 SDK 17.1.0 ddde560componentsdrivers...
I want to use the Zephyr Shell with my own transport layer. Since the only connection I will have to the modem is over SPI, I want to have the SPI read/writes handled with...
I am using sdk 17.1.0 .I am getting error while using bsp_buttons_is_pressed function in main although i have included file bsp.h ,bsp_btn_ble.h, boards.h. The error is Error...
Hello,
I've been developing an application with nRF52840 and I've been reviewing the appropriate SDK to start with. I see Nordic recommends starting with nRF Connect SDK...
Hello everyone,
I have a question regarding the bonding process in the NRF52832 device. Currently I have one custom service with one character and my nrf device is a doing...
