Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi, I took a look at the low power comparator example from the Nordic SDK and test it with my nRF52-DK and I found out that the comparator isn´t triggering when I set the...
Hello, I have a problem with the I2C peripheral on my nrf53840. I enable i2c driver on my project and read sensors on the bus. Everything is OK. Then when with Power management...
Hi Nordic,
I am working with the s140, sdk 15.3. My application is a central that should connect to a device that has several services. As soon as the connected event is...
Hello,
I am using nRF Connect for Desktop 3.7.1 with a nRF52840 USB dongle for testing purposes.
In the Bluetooth Low Energy 2.5.3 application I deselected the "Auto accept...
Hi,
I'm using Nrf52840 to connect to a Mobile via BLE.
I'm advertising to start connection, and after bonding, I can start advertising with whitelist in order to connect...
When adding this line to codes from an article here control reaches
Example used is ble_app_hrs_pca10056_s140 on nrfDK2 , sdk 17
==================added to advertising_init...
Hi,
I'm trying to use Thingy91 as a gateway for collecting data through BLE (from other thingy52s) and send it to Azure IoT Hub using LTE, but the current sample code only...
Archlinux
Visual Studio Code: Version: 1.58.0-insider
nRF Connect: v2021.9.98
I installed the "nRF Connect" extension in vscode, and went to look into a problem I was...
Hi,
I'm currently testing LPCOMP with one of our nRF5340DK boards.
The power consumption of the LPCOMP seems way too big (around 140µA) once enabled with this conf...
Dear Nordic Engineer
Our customer uses NRF52832 to develop a computer remote control pen. They are based on the keyboard example in the 15.3.0 SDK. Now they encounter some...
I have a working (hand-wired) prototype that connects to the internet without any problem.
Now I have made a PCB to replicate the same thing and loaded the same software...
Hi, I do have a PCA10040 board, I'm using the examples from Nordic. On the DFU example for SDK 12 I have pressed button 4 and RESET the board to active BOOT . I’m testing...
Hi,
S112/S113 is currently the only supported SoftDevice on nRF52805 and doesn't support Central (Only Peripheral). Is there a plan to enable S132, SoftDevice Central are...
Hi,
I have nRF52840 DK boards.
This is rather an informational question for my benefits.
In post: https://devzone.nordicsemi.com/f/nordic-q-a/9315/nrf52-802-15-4
...
Hi,
I’m developing a BLE joystick with nrf52832 with a PCA10040 board
To make the development simple I’m using 16 input Buttons and 2 analog inputs with 8 bits each. ...
