But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
i am using nrf9160 based custom board with zephyr, and trying to build GPIOTE with interrupt for a button, and led finally connect with PPI
i have been trying for...
Hi,
sorry if maybe I repeat the question. I have tested the central uart and the peripheral uart and I can make the two nordic nrf5340 devices communicate. I was also able...
Hi
I need help in understanding what the best practice is when retrieving messages from devices via nRF Cloud to my web APP.
I expect the devices to transmit messages...
I'm learning how the nRF cloud works and can't understand how the message flow is supposed to happen.
Devices send MQTT messages to nordic broker and then what?
I found...
Hi All,
I've got a project with an nrf51802, i'm trying to connect to it with a jlink edu to no prevail..
I'm running macos catalina 10.15.7 (19H15), nrf command line...
Path to sample: v1.6.1\zephyr\samples\boards\nrf\system_off
Board selected: nrf52840dk_nrf52840
-------
I am attempting to modify the sample to use a button connected...
Hello to all,
I have a problem with nrf52840 DK board, it was not detecting in nrfConnect with PC.
Previously it was working but when I had checked one sensor which is...
HI , All
I am debugging connection of "Chromecast Remote Controller" with ble_app_interactive.
I am trying to implement ble_app_interactive on nrf52832 as my application...
Good Afternoon,
I am using NRF51822-QFAA as ble remote in central mode. It connects to ESP32 and send the command for changing it's mode. I am using the RF module YJ-14001...
hi
my board nrf5340 do not run any ble example . it creates build and everything is good in softwre while running. but when i try to receive any signal from board of blutooth...
Hello,
I am new with nordic boards. I am using an nrf5340-(P)DK.
I bulit and downloaded the perhipher-lbs sample successfully to the board.
However, when trying to discover...
Hello All,
I am developing thread base system.
I am using SDK - nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8
Dev-kit - nrf52840
I am using mtd code for development...
Hi,
My project is combined 'Multi-link Central Example' and 'ble_app_uart', so that it is a central that can be connected to multiple peripherals and a peripheral that can...
Hi, do you plan to upgrade FreeRTOS? In nRF5 SDK v16.0.0, there is FreeRTOS v10.0.0 - at the time of writing, FreeRTOS v10.2.1 is available and it comes with a few fixes....
