We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I unsecured my device and running it with JLink RTT to observe logging. If I program uicr registers during this process, the devices gets secured and I have to redo...
Hi,
I'm BLE-sending out Sensor values using a nrf52832. When the sensor gets a (new) value an interrupt is generated and the nrf then transfers the value in the gpiote inerrupt...
Hi. I have read the documentation and I have a couple of questions:
What makes work different mesh_gatt and nrf_ble_gatt? Why can't they work together (maybe it's because...
hi professor,
I add the CONFIG_NO_OPTIMIZATIONS=y but ble connection timeout In my pheripheral project .When I delete CONFIG_NO_OPTIMIZATIONS=y, the ble will connection...
Dear Nordic Team and Community!
I have again a question concerning advertising. Currently I am working with the devices nRF52840Dongle (Advertising, S140, 10059) and nRF52840DK...
Hi, I'm using nRF52805. My "1 button to turn ON/OFF system" code works perfectly fine on nRF52 DK.
However, when I migrate the code to nRF52805, Segger shows me an error...
Before exploring the Zephyr ecosystem, I plan to study in detail the periphery of my microcontroller (nRF5340).
For this purpose, I plan to try examples from nRF5_SDK_17...
Hi we are designing custom Board using nrf52840 and want to use NFC as mode of communication. We want to use NFC in nrf52840 in 2 way communication mode. My questions are...
I just figured it out it is not I2C protocol. I need to write all the command by Bit-Bang mode.
How can I send/receive data with manual bit command to SHT1x sensor?
Can...
Hello,
I am trying to setup a windows docker image to use on a build server for zephyr nrfsdk projects, but i am haveing difficulty getting things configured correctly...
It was suggested in other cases that it may be more power efficient to use uart without easydma in some cases.
I am using NCS and I see CONFIG_UART_0_NRF_UARTE is defined...
Hi,
I am using Thingy91 and I successfully connected it to the cloud, also able to pull all sensor readings with the curl command: curl https://api.nrfcloud.com/v1/messages...
Hello!
I am starting to profile our device using the PPK2 and I am seeing some strange measurements when the device goes into its low power mode.
I'm attaching an image...
hi, customer use nrf52840 made mesh node. use nrf connect SDK v1.6. they have two quetion.
1: How to set 125kb low speed and long rang in BT mesh network,
2: How to enable...
Hello! We are targeting an nrf52840. We were able to compile and successfully use the mqttsn_client_publisher from the latest nRF SDK v4.1.0 for Thread and Zigbee. We then...
