But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I am using the nrf52840 controller for the development ,i want to read the value from 2 channel of ADC . I just gone through the SDK example code of
SAADC, here...
Hi All,
I was trying to transmit a bare-metal minimal C program to send a raw ADV_SCAN_IND PDU using nrf52840 dev board. Code is listed below:
Here is the linker script...
I'm currently building a device that has the following functionality:
1.) wake from sleep mode and wait 5 seconds for a potential button press
2.) if the button is pressed...
Hello,
I'm trying to debug an issue where a function I wrote that should only be called under a specific condition is calling in an infinite loop whenever the program runs...
Hi, I'm using nRF52805 S112 for my BLE project. I'm using an internal RC ocillator. I would like to ask something about the clock.
1) NRF_SDH_CLOCK_LF_RC_CTIV =16 and NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hello,
I am working on using the open_bootloader with our application and running into a problem.
We are using the GP_REG to jump from our application back to the bootloader...
Hello,
I'm using the following code to loop through the flash memory sequentially and send records created by the flash_fds example:
The data stored in the records...
Hi,
How does numeric comparison works? Shouldn't both devices share parameters in order to display the same number? How can we be protected from MITM?
Thanks!
Ive added another endpoint to the OTA zigbee client example, when I run
ZB_ZCL_SET_ATTRIBUTE (ep, ZB_ZCL_CLUSTER_ID_ON_OFF, ZB_ZCL_CLUSTER_SERVER_ROLE, ZB_ZCL_ATTR_ON_OFF_ON_OFF_ID...
I'm using the nRF52 DK and attempting to use I2S to send data to a DAC. I'm using the nRF5 SDK, version 17.0.2. The last sample in the data I'm sending is always replaced...
Hi,
I have a question regarding diffie-hellman.
What exactly are we doing with diffie-hellman key? Do we use it to create another key? Or is it the key itself?
Thanks...
Hello,
I am new to development with Nordic board. I have evaluation board from u-blox which is EVK NINA-B406 and I have installed Segger Embedded Studio IDE for development...
Hello,
I have been trying for days to program my nrf51422 project without much success. I am using a Jlink programmer. I have connected VTREF, GND, SWCLK and SWDIO from...
