But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello, For our nrf52832 custom board developed using nrf SDK 14.2, I need to turn OFF and ON LED accurately in terms of ms, hence after going through this page, I used Single...
Hi,
We are developing a device that should work in multiple mobile networks, and some of these are known to provide no DNS server. As using a fixed IP address for our cloud...
Hi,
I want to read the data from the a cceleration sensor by I2C. Several days ago, I added the code about twi bus to "ble_app_template" example , it worked well. But today...
I have a custom board, I am using to evaluate nrF52811 from eclipse (I just prefer this over SES).
I have installed S112 on the flash and also my application at 0x19000...
I'm communicating with N25 flash memory, the page size is 256 bytes. there is a page_program command which can write up to 256 bytes. there is no way to write in the middle...
Hi I'm trying to change peripheral usbd_ble_uart_freertos example to central with nus_c I added the scan and nuc_c module. When I'm testing the application, before making...
Hello, I am using:
NCS v1.5.1 and the sample code from ~/ncs/v1.5.1/zephyr/drivers/sensor/max30101/ (max30101.c, max30101.h) nRF5340dk MAX30101 from Sparkfun www.sparkfun...
I suspect this is related to https://devzone.nordicsemi.com/f/nordic-q-a/36601/gpregret-and-nrf_bootloader-c-evolution-proposal (Case ID: 211047)
In nrf_bootloader_info...
Hi,
I am going to use the usbd_cdc_acm example for the dongle.
I added the pin definitions as below:
#define TX_PIN_NUMBER 13 #define RX_PIN_NUMBER 15
and changed...
hi
I use nrf52833 and nRF5_SDK_17.0.2_d674dde HID keyborad demo.
1. I pair PC success first , then I erase_bonds ,and repeat pair my pc. with other address but PC do not...
I'm performing power measurements with nrf9160-DK running the Serial LTE Modem application.
The example SLM has been modified to add support for HTTP, MQTT and also to relocate...
I have been following the NCS BLE tutorial part 1: Custom Service in Peripheral role - Getting Started - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com) for BLE and...
Hello,
I use nrf52832 and SDK 17.0.2.
I use flash crashlog to store crash log on the flash.
I enabled NRF_LOG_BACKEND_FLASH_START_PAGE = 0, which means flash log area...
Hello,
I have a problem with the GPS and more precisely the AGPS. I would like to retrieve my position with the thingy91, I created a project by taking the AGPS sample and...
So, for a while I have tried to follow these instructions: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
