We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi, My name is Philex Fan who is a researcher working in academia. I am working with a group of researcher to develop biomedical device that can get brainwave signals and...
Hi!
This tutorial is just for current > Measuring current . I want the same for latency with code.
I'm working with two nrf5340 for Bluetooth low energy and I want to...
Dear Community,
From a provisioner, I want to get the MAC address of a device (provisionee) during the provisioning process. Is there an example somewhere in the forum please...
Hello,
I am using nrf52805 processor, nrf sdk v16.0.0 and Segger embedded studio. My board communicates with a temperature sensor over I2C. The software is working without...
Hi all,
I am working on a ble5 beacon with ecdsa signature. I would like to use mobile to verify my message. As I see that the crypto ecdsa example use raw key and generate...
I have developed an APP using SDK 15 (both BL and APP) updating Bootloader and APP which is working fine.
I have developed same app using SDK 17.0.2 (both BL and APP)
...
Hi, I know this topic has been up in several posts before, usually ends with, buy a LitePoint or Anritsu.
Assuming you want to do a poor mans measurement setup, just relying...
Hello, I've been trying to get the nrfx_i2s driver working with Zephyr, on the cpuapp core of the nRF5340. After configuring the driver, setting CONFIG_NRFX_I2S in prj.conf...
I've been successfully creating custom services, but there is one case where a device has a service UUID and it's 2 characteristics have completely different UUIDs (all 128...
Hi,
How do I set ncs v1.5 to save the last open project path?
ncs v1.3 has the last open road
ncs v1.5 does not have a project path that was last opened
Here's the...
Hello, I have a question. In the HID_keyboard routine, I have already bound two phones.
Now I want to cancel the binding, and the function was called by key interrupt pm_peers_delete...
Hi,
I am new to the zigbee development and currently going through the documents.
My end goal is to develop a application that measures the level of a tank using radar...
Hi
We are using an external 32MHz crystal to generate the internal 64MHz clock.
As described in several examples, we start the HFCLK with
NRF_CLOCK->TASKS_HFCLKSTART...
Hi,
I am using nRF52840 and SDK 17.0.2. I used to write data using nrf_fstorage_write() at some address of Flash and I want to read the same data using nrf_fstorage_read...
Hi Nordic,
We created a firmware based on the eddystone example in nRF5_SDK_17.0.0_9d13099,
I modified the macro APP_CONFIG_ADV_INTERVAL_MS_MAX in es_app_config.h from...
