I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi
I got it PPK2 and tested.
PPK2 is very useful compare to previous version PPK.
I wanted to sampling time expanding to 10min.
But i see that 2min time sampling...
Hello,
I would like to save some keys securely using the Infineon OPTIGA Trust X chip. To do a quick test I bought the Infineon shield2Go with the OPTIGA chip that I connected...
Hi All
as title.
I am nRF52 DK PCA10040.
Chip select is nRF52832.
I measure out from wfe to Timer Interrupt time is 1.3us.
Is it correct? and How can I reduce the...
Hello,
I am working on a school project with my team that requires one master device and up to 30 slave devices which will be controlling LEDs. I was thinking the nRF52840...
When enabling BLE on nrf52840, we are using specific API to access flash erase and write commands. All is working fine 99% of the time in term of read / write / erase into...
Hi Sir We are scanning nearest BLE using NRF Scanner example using 1- NRF52840-DK and 2. BT840 . We are getting good RSSI value using 1 but very poor RSSI values when we are...
Hi,
I am using nrf52832 with s132 softdevice and SDK17. I want to disable bonding and pairing in ble_multirole code. I have tried disabling the SEC_PARAMS_MITM, SEC_PARAMS_IO_CAPABILITIES...
Dear Sir,
I am using SPIM , EasyDMA array list,with following flags
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER , NRF_DRV_SPI_FLAG_RX_POSTINC , NRF_DRV_SPI_FLAG_HOLD_XFER&
...
Hi,
I am using my nrf52832 board with a MPC9808 sensor and I wanted to use the example code provided in zephyr/samples/sensor/mcp9808
Can you tell me with which pin of...
i'm building an amplifier that can play sound over bluetooth. I intend to use the nrf52832 to send i2s data to my dsp chip. based on the loopback example, i have an idea on...
Hello,
I was reading through the code of the asset tracker application and noticed that there is no while(1)/for(;;)-loop. I see this for the first time in a board application...
hello,
we are in process migrating to SDK 16.0 and service pack 8.27 or higher. While performing an upgrade we encourage few problems and would like you expert advise...
2 Questions, both short:
1. Documentation error in Softdevice 15.x and 14.x header files:
/** @note If any of the discovered services have 128-bit UUIDs which are not...
