But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
When I open J-Link RTT Viewer application to see logs of a program with set CONFIG_LOG_BACKEND_RTT , then I see logs' output with some delay, comparing to logs of the same...
Hi.
Can you make a youtube video showing how to use SEEGER studio for a demo project.
I would like to see the whole workflow starting with a new project for nRF91xx where...
Hello,
I'm developing an HID consumer control application with the nrf52832. As many ble products have, I would like to add a power off button to my pcb. Is it better to...
I'm just after C headers and Makefile like the NRF5 SDK.
All I found was some "AppImage" file for x86_64 which I've no idea what to do with - I tried unzipping it, but it...
Hi!
Whenever I open an example for the nrf52833 (PCA10100) in SES I get the error "The evaluation period for this release has now expired". This does not happen when I try...
I am working on nrf52832. For my task, I need to knoow how nordic find out the Total average current on Online Power Profiler for BLE( https://devzone.nordicsemi.com/nordic...
I wanna try to connect multiple device with only one Android, but I don't know how many devices Ble can connect to only one Android. When I try demo on Samsung galaxy S8,...
Hi,
I have an issue that is urgent for me, as we wish to add DFU capabilities via pre and post production hardware. I am using Android 10 on Samsung Galaxy A10 to test...
Hi,
I was able to create a device driver support for a DAC, model TI DAC80501Z. In the first place I put the driver in zephyr/drivers/sensors.
I works fine.
Then I made...
Hi Team,
Please provide the nRF52 based module Characterization, software testing for FCC/IC/ETSI certification test procedure and document
Is DTM test enough for FCC...
According to SDK documentation for GFX library :
“After generating a font, you must change FONT_INFO::height to be described in bits (pixels), not pages”
But in the provided...
Hi,
I can build the blinky_pca10040_s132 example and I loaded it in the nrf52840-DK without errors but nothing happens in the bord I can´t see any lead blinky.
Please...
Hi
We are sending devices for RF/wireless testing and need test firmware that allows for the Bluetooth frequency and transmission power to be easily adjusted. Does Nordic...
Hi.
As you have made a progress in your development of both hardware and software. It would be greate if you remove old videos from youtube. I have just spent some time...
Hello.
I am using nrf52832 and Segeer Embedded Studio.
I want to add a timer function to the ble_app_uart example so that the sensor value is read every 50 ms.
So I...
