This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
nRF5340 with NCS 1.4.0.
I'm using the NUS (code derived from central_uart & peripheral_uart sample) and i'm trying to send longer frame.
I have tried to add the following...
Hello,
I was trying to recreate the blinky program for the nrf52840dk using the nRF5sdk using Segger embedded studio.
I tried doing it by opening the blinky example code...
Hello ,
I am using nRF52832 , sdk 16version. I want to set the BLE connection interval via BLE using application. How to do that? I tried to assign the variable to the min...
Hi everyone,
Regarding the CDC ACM example I have a question. In the example, every time a button is pressed there is a writing. I would like the writing to happen every...
We are trying to use more than one nRF52840 dongles simultanuously on the same PC and within the same process using the pc-ble-driver library (pc-ble-driver library version...
Hi. I want to save sensor offset data to flash memory on chip.
I erased page 126 first, but no events were called.
I can only get 0 from the value of sd_evt_get function...
Hello Nordic Comunity,
I am new to the Nordic nRF52840 DK usage. I am working on the development of a connectable beacon for a longer duration.
Any type of help will...
Renode ( https://renode.io/ and https://github.com/renode/renode ) is an open source simulator and used by Zephyr OS for example to validate binaries for different architectures...
Hello Nordic Taam:
I follow the WEB steps below
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v4.1.0%2Fthread_ot_performance_measurement.html
Software...
I'm designing a EEPROM type of memory using a SDCard. The write and read functions works fine, but the initialization does not work sometimes and it stays in a loop (because...
The size of flash of softdevice in the "s132_nrf51822_5.0.0_release-notes" is 0x23000 but atrually the size of the flash used by softdevice is 0x224A7, which I found when...
We are using nrf9160 as an LTE-M modem with the serial_lte_modem app running on it. Another chip (ESP32) communicates with it using AT commands and after a few minutes of...
Hi team,
I am working with nRF9160DK on NCS v1.3.2.
I am building the asset_tracker application and from my understanding when running running west build -b nrf9160dk_nrf9160ns...
Hi, I just got my Thingy:91 and I'm trying to run through the getting started guide. On the nRF Connector v3.6.0 app, it doesn't change from "no devices available" to "select...
