Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I want to develop a mesh network where I can send/receive data from one device to other devices(sleepy sensors) through relay/router node (always on).
For example
A (Publish...
Hi, engineer:
I need to compute FFT on nrf52840, I used sdk-demo fpu-fft, I tested the FFT operation time and found that it took 2 ms，That`s a long time, Did I configure...
Dear all, I have a problem with nRF52811 GPIOTE input interrupt. I have one sensor interrupt pin at GPIO P0.30 with external pull down resistor. I am able to config P0.30...
Hello community,
I have programmed my dongle as beacon. Now I want to stick them to the wall for experiment purposes. How is it possible to power them up via external...
Hello
I am considering a product that connects several NRF52840s to a USB 2.0 7-ch HUB and works with 30 BLE devices. When reviewing a product like this, there are some...
Hi everyone,
I have one question just for confirmation.The available analog pins on nRF52840 DBK are those provided by header P2 (six in total)?
Are there any more available...
Hi,
I'm working with NRF52832 in a BLE mesh project and I'm a newbie in this filed.
Project description:
- There're 5 devices in a BLE mesh network.
- In each device...
Hello,
in the corse of implementing pairing / bonding on top of the softdevice, I was looking for examples. The only example I've found, that seemed to not use the peer_manager...
Hi,
Currently i am developing BLE communication software for Android and iOS
This software is under Ionic development.
Is there any solution for Ionic/ Javascript development...
Hi !
When i try to open gps sample and enable SUPL client support with CONFIG_SUPL_CLIENT_LIB=y, i received this alert so i cant import project file:
I already have...
Hi all, I am working on light switch example and I want to perform different LEDs have their own switch, i.e. button 1 control LED 1, button 2 control LED 2. The problem is...
Hello,
I am working on a project where I can have Voice over IP on the NRF9160 DK. I am now working with a I2S microphone ( https://www.adafruit.com/product/3421 ) at the...
Hi,
I am setting a nrf52832 for an OTA DFU using BLE. I am on windows.
After managing to run the Secure DFU Bootloader following the getting started , I am trying to merge...
I'm using s140_nrf52_6.1.1_softdevice and nRF5_SDK_15.3.0_59ac345 on a nRF52840.
We are trying to verify that, indeed, we are successfully entering and using coded phy mode...
Hi!
I've been having some issues with the ppk recently. I've been trying to measure the current on our custom board but it was showing way too much so I tried on the DK...
