But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi there. When nrfx_gpiote_in_init's event handler is called, is it being called as an interrupt? I note that if I use NRF_LOG_INFO within the body of the event handler, then...
Hi everyone,
I am following the qspi example to communicate with MX25R6435F flash memory. This is my first time interacting with a flash memory and I have some questions...
Hello!
i´m enable ble long range like central for scanner beacons, i can see long range beacons, but only one time, then i need to restart my DK: i use to do this ble_uart_c...
Hello,
As per your given link in 1.2 Build and flash - using SEGGER Embedded Studio ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts...
Hi,
It appears that at least one Mesh_v4.2.0 example (light switch) will not link under nRF5_SDK_17.0.2.
I managed to get Mesh examples to run under SDK_17.0.0 a while...
I have a new Bluetooth remote product in development that has a bluetooth stack that will incorporate HID, BAS, NUS, ANCS, and buttonless DFU services. I have the HID and...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm getting this error while trying to connect with my device in the "ble_app_hrs_c".
"Connection...
I have found a few "how to" on cofiguring Eclipse for application development on nRF52 devices. After some point things are not as described in this guides. So, Is there any...
I'm trying to create a read event whenever a certain characteristic is read. I used BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event to monitor that. I also set "is_defered_read"...
Hello,
I am developing a composite HID peripheral based on the nRF52840 that can connect to a PC either via USB or BLE.
I am using SDK 15.0.0.
Regardless of the connection...
When I build and run an example Bluetooth: Peripheral HIDS keyboard (it's the same for master branch and v1.3.2) using nRF52840 DK I faced one strange behaviour. To simplify...
I just downloaded the latest version of the pc-ble-driver hoping some of the bugs I had reported were fixed. The downside is the notes do NOT indicate they were addressed...
I'm working on an nRF52840 design where we may get away with only the outer pin row on the package.
However, one pin on the inner row of harder to reach pins seems important...
To the kind attention of Nordic support team,
I'm considering here a scenario where only a device and only an host PC are involved. They are ble bonded together.
Now,...
I have been working on receiving data from sensor using nrf52832 and I have been successful in getting the data and printing the same in the app. I have also been succesful...
