Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi:
I believe this is possible but will ask anyway. I am working on a device that connects to a BLE central device (a cell phone). I would also like to send advertising...
Hi to everyone!!
I have this error:
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_fprintf (referred from nrf_log_str_formatter.o). .\_build\nrf52832_xxaa...
Hello, I attempted to make SES thread aware by following various support threads in this forum but unfortunately the SES just doesn't show any threads. I have tried with 2...
Hi,
I running a custom application on nRF5340 PDK using zephyr (2.3.0) and nordic SDK (1.3.0).
I tried to build Zephyr HID examples and got an error. (I don't think it...
I am using an example from Nordic that enables a central to connect to several peripherals via UART. The connection is automatic (the key is if they all share the same NRF_UART...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi, so i'm using Visual Code with PlatformIO to build an example with arduino-bluefruit-bleuart the build runs perfectly but after i upload it into the Nordic the bluetooth...
Dear Sir, I need 2 interrupt handle on 2 PIN, I have set 2 GPIOTE event: #define PIN_INT1_ACC 4 // INPUT Interrupt INT1 from ACC #define PIN_INTB_ECG 8 // INPUT Interrupt...
Hi, I have a set up consisting of an nRF52840 and Raspberry Pi communicating over IPSP following the zephyr OS sample docs.zephyrproject.org/.../README.html My application...
Hi,
I've been using XMONITOR command to check some radio parameters. ATM, I am checking those once/minute, right before requesting power save mode from modem. After updating...
Hello,
I wondering if I use the nrf5_SDK_for_Mesh_v4.2.0_src light switch example and modify it to suit my needs.
Q1. I want set up a proxy node using nRF52832 so that...
Hi,
in https://devzone.nordicsemi.com/f/nordic-q-a/24115/io-pin-signal-during-reset it is mentioned that the pins of the nRF52832 get set to input _during_ a reset.
...
This is my RTC init function. Whenever I start advertising in fast-advertising mode, and timeout for fast advertising expires, the RTC2 timer stops running and COUNTER resets...
Hello,
I am trying to make a simple power optimized BLE peripheral device based on nRF52840.
Here is the chart from the Power Profiler
The device advertises once in...
