This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello, Following is my development environment IDE: Segger SDK: 16 SoftDevice: S132 Right now, we are trying to merge the following two examples. - examples/peripheral/nrf5...
I'm looking for a simple demonstration application that can run on the nRF52 Dev board and communicate with the default Thingy52 firmware. My plan is to get this working on...
I'm trying to read the Device Name from address 0x21 on a BQ40Z80 fuel gauge, using my nRF9160 chip, connected via SMBus.
When polling the address space, I nicely get an...
I'm using Ubuntu 20.04, SES 4.52c, SDK 16 nRF52840 DK board.
I'm going to need to use the PWM driver to supply clock pulses to an I2S microphone and the I2S peripheral running...
Hello all, I've run into a weird problem that hopefully someone has a clue. My environment: - PCA10040A, nRF52832 - sdk 17.0 - softdevice s132_nrf52_7.0.1_softdevice.hex ...
Hi:
I have a set of 2x Thingy:91 and 2x Thingy:52
I want to make a setup where the devises work in line over a longer distance. T91-T52-T52-T91 is that possible all working...
I want to run the realtime counter RTC2 with softdevice S132 WITHOUT an interrupt handler. I have no purpose for an RTC2 interrupt handler in my code, as I simply want to...
Hello,
i have issues getting the new softdevice into my product.
nRF52832 with 512kB Flash and 64kB RAM.
Currently i use s132_v6.1.0, a bootloader and an application...
Hello, I am developing an application with nRF52 DK. softdevice 112 and SDK V15.2.0. This is a "continuation" from my previous ticket ( https://devzone.nordicsemi.com/f/nordic...
Hi Devzone:
I am having trouble finding the right information to get ozone to run on Nordic nRF52833 with my own project. I followed in instruction here: https://wiki.segger...
Good afternoon everyone, I am facing problems using libuarte example (SDK 17 and NRF52 DK. Using SES and S132, PCA 10040) It works well with puTTY or other software, but I...
Hi, I have a question about Bluetooth pairing control.
I use nrf52dk board and sdk v17. I am working on many things using the example of sdk.
Now I'm trying to control...
Hi all,
There is a question that I want to figure out.
I have a nrf52 board which supports to use DMA to receive data from UART. So what would happen when BLE radio interrupt...
